THE TM MWS thread

[Sawyer]

Just these ones. Got mine off a mate, but various places sell them, they're just called MAGPUL Magpulls.

Can you link me to what you use?

Thanks!

Also, anyone have recommendations on what handguard I should get if I want a 9.5in M-Lok handguard? What brand is best? Also, outer barrel brand suggestions?

View attachment 51243

 

[hunter511]

Jesus H Tittyfucking Christ.............

I know the pound is weak, but £140 plus customs fees for an upper reciever (no internals) from impulse101.......... yeah, they can honestly go fuck themselves.

Soooo anyone know a good option for a 9inch drop in outer barrel assembly for the mws? Got the bits for a BCM recce9 inbound just need that outer barrel goodness. 

 

[the3rdlegion]

Can anyone link me the adapter part(s) that I need to use third party handguard rails with the MWS?

 

[Guest]

Can anyone link me the adapter part(s) that I need to use third party handguard rails with the MWS?

 
https://www.fire-support.co.uk/product/pts-adapter-ring-for-marui-m4-mws-gbb

 

[Uncle Pauly]

Just these ones. Got mine off a mate, but various places sell them, they're just called MAGPUL Magpulls.

View attachment 51243

Stupid question... but I assume you need to remove them when filling the mags with gas?

If so, does it prove to be a bit of a faff during busy game days, or are they easy enough to get on/off in a hurry?

 

[Sawyer]

Stupid question... but I assume you need to remove them when filling the mags with gas?

If so, does it prove to be a bit of a faff during busy game days, or are they easy enough to get on/off in a hurry?

Easy enough to pull on and off. Green gas modded gas need filling less often, so it's not a major issue, more a minor pain.

 

[Uncle Pauly]

Thanks for the quick reply! ?

That’s good to know. I’m considering getting some (and my mags are all GG modded).

 

[Hypokondrikern]

Stupid question... but I assume you need to remove them when filling the mags with gas?

If so, does it prove to be a bit of a faff during busy game days, or are they easy enough to get on/off in a hurry?

I have these on all my mags. You simply fold the flap sideways which gives space to fill up the gas. So, there is no need to remove them. 

 

[DopeYourScope]

I have these on all my mags. You simply fold the flap sideways which gives spaces to fill up the gas. So, there is no need to remove them. 

Same here, I got a load of issued ones from a matey on eBay, think it was £15 for 6, get genuine magpul ones they’re about £2 more expensive than the repros except they last more than 15mins and actually grip the mags.  

 

[Sawyer]

I've got mine on the wrong way, and pushed on as far as they'll go, deliberately, so I've got no flex in mine to do that.

 

[Jacket]

Anyone have experience with the PDW style sliding stocks? Do they still allow the rifle to cycle reliably, any loss/increase in recoil strength?

 

[Cipher-032]

Anyone have experience with the PDW style sliding stocks? Do they still allow the rifle to cycle reliably, any loss/increase in recoil strength?

Ran a G&P one for a little while. Gun worked perfectly fine, but the notches on the stock more out incredibly quick. Meaning that you couldnt lock the stock in a position you wanted. 

Mine could of been a lemon...

 

[Whisky1]

Hi, Guys, i recently got the G&P 5.0 red Nozzle Valve. Semi it shoots like a dream except it needs more of a full gas load and on full auto the cycle is slow and fast at the same time. It seems like the timing is off. With the original parts everything is fine and ROF is satisfying. What should i buy, is it all about stronger springs?

This is my beauty

View attachment 51169

Make sure you bolt isn't catching on the return.

Can I ask what scope mount that is? 

Whisky.

 

[Seven]

@Wo1f Quick question, not sure if you covered reasonings but I can't see it... But what is the benefit of leaving a stub on the magazine fill tube instead of removing it entirely?

I'm on the cusp of buying a CQBR block 1.

 

[Wo1f]

@Wo1f Quick question, not sure if you covered reasonings but I can't see it... But what is the benefit of leaving a stub on the magazine fill tube instead of removing it entirely?

I'm on the cusp of buying a CQBR block 1.

It seemed to give slightly better consistency, but mainly because it’s easier to cut than pull out. 

 

[damster117]

Thanks for the info guys, mostly set up with the two loadouts. One long and one short. Gotta be ready for all scenarios !!

Hearing talk about the angry gun nozzle I might give that a try. The dmr is running 1.3J at 0.28g. Both with Dave's brass nub installed.

View attachment 50795

I take it that's the PTS gas version of the magpul UBR stock?  Does it fit and operate ok? Does it affect the buffer operation at all?  Looks awesome!

 

[sonofsammo]

If anyone has a clue about HPA and the MWS, please could you pop along and have a look at this:



Any advice would be most welcome!
(I made a new thread so as not to clutter this one).

 

[hunter511]

Anyone else waiting on bits from Angry Gun? At the moment my bolt left China a week ago today and has still not arrived in the UK? That strikes me as one hell of a high endurance plane.......

 

[Guest]

Anyone else waiting on bits from Angry Gun? At the moment my bolt left China a week ago today and has still not arrived in the UK? That strikes me as one hell of a high endurance plane.......

you don’t order much kit from China do you ???

 

[hunter511]

Having ordered from WGC, DenTrinity, RSOV, EbayBanned etc I am familiar with the general deal. At the same time given the hypersonic speed with which the first BCG was recieved in this group and the fact that AG is (presumably) an established business, not just a random 1 dude and a storefront I would at least expect updates after paying for the more expensive shipping...........

However it is unusual for the Royal Mail to take this long to tell me I owe them a hostage fee plus customs.....