THE TM MWS thread

[LVOA-D]

So far everything has been a drop in fit! Actually surprised, even the SI dust cover fits perfectly. Only "strange" bit is that the forward assist stick out more than it probably should.

View attachment 46517

View attachment 46518

View attachment 46519

View attachment 46520

 

[Guest]

Looking good ??

 

[Groszq]

Hi!

Could you tell me what upgrades are worth doing in TM MWS? I already changed hop up bucking and inner barrel. I am from Poland, so power is not an issue as long as I am beneath 2.81J.

 

[Davegolf]

2.8j!!!

 

[hunter511]

MTR specific question, how in god's name do you get the barrel nut off? Seriously even with the correct tool Ive had stop before I mangle it.....

On a related note what the hell are the wierd not quite Torx screws on the MTR as well?

 

[Guest]

MTR specific question, how in god's name do you get the barrel nut off? Seriously even with the correct tool Ive had stop before I mangle it.....

On a related note what the hell are the wierd not quite Torx screws on the MTR as well?

They are all thread locked on.

I believe the screws are Bristol head

 

[hunter511]

There's threadlock..... then there's the barrel nut on that solidly I suspect its been welded. Anyone know how cerakote handles heat? Thinking about getting a blowtorch on it......

 

[LVOA-D]

@hunter511 I am not in the position to give advice about uppers and barrel nuts, so I won't. What I do want to say, good luck and don't be like me! ?

 

[Guest]

There's threadlock..... then there's the barrel nut on that solidly I suspect its been welded. Anyone know how cerakote handles heat? Thinking about getting a blowtorch on it......

You can’t see the barrel nut when the rail is on, I put the upper receiver in a block and used a drift to get it off.

 

[hunter511]

My intention is to replace the rail with something a bit sleeker anyway to be honest. I'm hoping to get the MTR specific barrel and ris mount assembly off un-brutalised but if necessary I'm willing to move into the realms of "extreme prejudice". 

 

[itsme]

when do you guys feel the need to clean and lube everything up?

after every game, after every x games, after x shots?

went to my first game with the mws and it performed so lovely :wub:

 

[Crazy_Crystal]

I do mine when I feel it needs it... super helpful I know ?

but basically this is a quick clean after most games to get any dust and muck out and re-oil or a more thorough clean with a barrel clean, wipe off any old lube then a full teflon spray on the trigger group and re-oil to displace any water or dirt if the weather conditions were awful, like the rain all day last Saturday, or if it's really dusty etc.

I'm sure others have their own routines though...

 

[damster117]

I do mine after every game, always a bit grubby in there.  I have a modify tan hop rubber which shows the dirt up easily and the gas I'm  using is a little dirty so I just clean the hop rubber and barrel with isopropyl alcohol, then degrease the receiver and bolt, then re-lube all the bits that touch with two different dry lubes, thinner wd40 dry on the bolt outer, with thicker teflon dry lube made by finish line for bicycle chains on the firing mechanism and on the groove the cocking handle runs in to make it smoother action.

 

[bapexxx]

Hi everyone,

I am getting back into airsoft and getting my tm m4 mws ready.
I have recently purchased the PTS EPG pistol grip (GBB version) for my M4. There is a washer and a little cog/gear thing that comes with the pistol grip.

Now the question is where should I install the washer and that tiny gear/cog thing or whatever it is called?

Thanks in advance.

 

[Crazy_Crystal]

Hi everyone,

I am getting back into airsoft and getting my tm m4 mws ready.
I have recently purchased the PTS EPG pistol grip (GBB version) for my M4. There is a washer and a little cog/gear thing that comes with the pistol grip.

Now the question is where should I install the washer and that tiny gear/cog thing or whatever it is called?

Thanks in advance.

the small cog is called a star washer and fits directly under the mounting bolt to stop it vibrating loose.

I hope that helps.

 

[bapexxx]

the small cog is called a star washer and fits directly under the mounting bolt to stop it vibrating loose.

I hope that helps.

ahhh! gotcha! thanks!

 

[bapexxx]

sorry for another possibly a noob question...

I have just install the laylax bad level on my m4 and now the bolt catch isnt catching lol.

Has anyone experienced the same issue?

Thanks

 

[LoneWolf]

Hello guys new mws owner here and also new forum member, iam happy to join your mws team...sorry if my English isn’t perfect.

So what’s your opinion for the Tokyo arms multi length cnc outer barrel , how it fits the upper receiver? 

 

[Yukarin]

I tried installing a BAD lever on my MWS too, it doesn't allow the bolt catch to engage properly either, I've tried filling the lever for a better fit, but I have a theory that its the weight of the lever that stops the bolt catch from engaging properly. I'm yet to find a solution.

 

[Katana]

 So this happened. Modify tan just crapped on me after like 300 rounds. Back to TM I guess. I'm thinking a lemon? I used only Geoffs and g&g bbs. It was definitely working and definitely installed right. The nub is the six g one. 

Dayum

View attachment 46595