• Hi Guest. Welcome to the new forums. All of your posts and personal messages have been migrated. Attachments (i.e. images) and The (Old) Classifieds have been wiped.

    The old forums will be available for a couple of weeks should you wish to grab old images or classifieds listings content. Go Here

    If you have any issues please post about them in the Forum Feedback thread: Go Here

THE TM MWS thread

Welcome to the club! What Dave and Jimmeh said sums it up pretty much! I am not in the position to give any advice anyways as I end up destroying pretty much everything I touch :D

 
holy shite you guys are fast :D Thanks for the detailed and quick replies guys! 

Can't wait for my mws to arrive!

if i use a barrel adapter is there a chance my accuracy will drop? 

I rly just want to take of the front sight cause i dislike it a lot but i read the gastube needs it. 

 
You wont lose any accuracy in the gun running a different rail and barrel adapter.

You can remove the FSP and fit a gas block as done a few posts back.

The gas tube serves no purpose but you need either a FSP or gas block to retain the RAS mounting ring.

Either that or you completely ditch the RAS setup and fit a free float rail system.

 
Just ordered the John Wick Conversion Kit... I shouldn't take days off, way too expensive as I had ordered a flashlight (Streamlight Protac HL-X 1000 lumen light inc. the Cloud Defensive Rail mount for the pressure pad) for the MWS this morning aswell ?  No idea how I am going to explain this one to the missus, thank god she won't be home until later tonight.

View attachment 45732

View attachment 45733

 
Just ordered the John Wick Conversion Kit... I shouldn't take days off, way too expensive as I had ordered a flashlight (Streamlight Protac HL-X 1000 lumen light inc. the Cloud Defensive Rail mount for the pressure pad) for the MWS this morning aswell ?  No idea how I am going to explain this one to the missus, thank god she won't be home until later tonight.

View attachment 45732

View attachment 45733
I'm praying for you brother ? 

 
@LVOA-D You are a braver man than I am and I used to race Cars at nearly 200mph! 

If you are going to sell the bits you don’t need then I would be interested in the Rail/Outer Barrel etc. ?

 
Last edited by a moderator:
@RobHedley If I didn't get scammed I will give you a shout when it arrives. Should arrive late next week, early the week after that. Basically what will be left is the rail, outer barrel, gas block (providing the Strike Industries one fits), gas tube and the flash hider. Also it is not bravery, it's stupidity combined with an addictive personality disorder(I googled that, probably most people on the forum here could be diagnosed with it) :) .

 
@RobHedley If I didn't get scammed I will give you a shout when it arrives. Should arrive late next week, early the week after that. Basically what will be left is the rail, outer barrel, gas block (providing the Strike Industries one fits), gas tube and the flash hider. Also it is not bravery, it's stupidity combined with an addictive personality disorder(I googled that, probably most people on the forum here could be diagnosed with it) :) .
Cool, sounds good. They are exactly the parts I was after!! I look forwards to hearing from you. ?

You may have an addictive personality but you will end up with the coolest toy!!! 

 
Last edited by a moderator:
Hello guys, Today i have received a lot of parts, that i will post my findings later, but before that i just have a quick question

does any of you have change the Hop Up Chamber for one of those either angry gun or Laylax CNC Hop up Chambers? if so are they any good ? is it  worth the change like is a must? or more like nnaah up to your taste?

Thanks for the replys !! cheers

 
@Kayzeroth Just me personally but stuff like that I usually do not upgrade unless it breaks. I doubt just replacing the chamber will have any effect anyways although I am not an expert about anything hop-up related, just my view.

 
Some of the aftermarket hop chambers allow the use of longer Nubs but otherwise there's no real performance gain.

 
Okay hive mind,

Can one go for too short an inner barrel, looking at building a very stubby (sub 10 inch including can) upper for cqb use with .25s. Im wondering if overvoluming will be an issue using 144a and stock bolt etc? For illustration something like the front end on this

42705AC1-7113-4C04-B742-D71CECD33CBD_zps8aukmx1u.jpg


 
hi @hunter511

the thing with almost all gas guns is that they release much more gas down the barrel than they actually use so they are effectively all massively over volumed anyway. but you will almost certainly be fine on 144 using .25 s. in fact the issue with joule creep is normally encountered when you can run much heavier ammo (I run .36s)

the short barrel will make it pretty noisy but yes you certainly can put a shorter barrel on it without any issues if you can find one you like that fits.

I hope that helps a little anyway ?

 
I had hoped that would be the case. Just didn't want to build an upper that was incapable of consistancy. 

 
Because of the way a GBB works it will always automatically adjust the volume based on BB weight and barrel length.

The floating valve works on pressure differential.

Basically you will have no adverse affects running a short barrel

 
Out of interest, has any one had it where their recoil spring has become stuck inside the buffer tube? No amount of pulling (carefully not the stretch to much) nor twisting will break it free. Im a bit baffled.

Its not detrimental. I can still use the gun.

 
Assuming that if you push down the release button the spring pops out but you cannot remove it from the buffer tube?

 
The gun i ordered is still not in stock ugh. 

Few questions:

What are some things i should order in the meantime to have as spare parts?

Which ring do i need as adapter for aftermarket handguards?

Do you guys ever run into problems playing on days where its like 6°C?

are there any upgrades but the greengas mod i can do to play in such tempratures or maybe even freezing weather? maybe this?: https://www.fire-support.co.uk/product/dynamic-precision-aluminium-lightweight-bolt-carrier-type-b-black-for-marui-m4a1-mws

 
Last edited by a moderator:
Upgrade time!!

I ran the CQBR totally stock on Wednesday  at the Bunker in Portsmouth. Ran faultlessly and was shooting like a laser on .20 tracers. Crono’d At 270 FPS on Abbey Vertex gas.

Having already bought a Modify Tan Bucking and a SixG Super Nub, I wanted to fit them so I ordered an Orca 6.05 250mm Barrel. I have to say props to The Cage Airsoft. I order the barrel Friday early afternoon and it was in my hands Saturday morning with standard delivery!! 

Got round to fitting the parts on Sunday. I started off getting a bench mark by firing .25 bb’s. I did some video but you can’t really see the bb’s flying so pretty pointless! They were reaching out to about 50m maybe a little shorter.

Stripped the MWS and fitted the parts. Pretty simple despite it being the first time I have ever done anything like this before. Loaded the mag up with .4 bb’s and after a little bit of hop adjustment they were flying straight and true. Judging by eye the .4s are still motoring some when they pass the point at which the pre change .25 bb’s drop down. Very impressed! 

2 things of note, I had to put the hop up fully on to get the .4 bb’s to fly straight. Is this correct? As in are .4’s the heaviest you can fire? Also I was using BLS Ultimate Heavy .4 Bio BBs (got them from Camoraids when I purchased the rifle). A few of the bbs split as they came out of the end of the barrel and I noticed that the magazine follower had a white line on it with what looked like bb residue. Having never used bio bbs is this normal??

View attachment 45808

View attachment 45809

 
Last edited by a moderator:
So what's your experience with Redwolf airsoft? Made some minor orders without issues there before except for som garbage rail they slinged and refused to take back. Anyways sent them an email with s pretty large order requrdt, approx 30 items incl and M4 mws lots of internals and lots of externals from magpul and strike industries. Reason I mailed them was most of the items were out of stock (as usual) but was hoping they could source home an order in the near future and also give a decent price on the order (+$2000).Some strike industries items were not listed at their store but they should be able to grab home those items if you are a reseller. But NOPE, got a shitty reply in bad English that said please use our email notification for out of stock items and something about a factory I did not understand. What shitty customer service is that? Sure it's not a huge order but still a decent amount. Pissed me off something fierce. //Rant off

 
Back
Top