Gun picture thread

[Nick G]

The WE MP5 SD turned up today. Ordered from Bespoke on Tuesday night so pleased with that.

Feels very nice, only tried it in the garge , but seems to shoot well and 3 round burst id fun.

View attachment 137743

 

[MistakenMexican]

Same upper, but different lowers.
 

GHM9 Gen2 ??
View attachment 137854View attachment 137855
 

GHM9 Gen1

View attachment 133464View attachment 135337

 

[GothicGhost]

View attachment 137742

fresh TM / Guarder build  

Thats's really nice, what Guarder kit did you use and did have to do any modifications?

Thank you.

 

[JimFromHorsham]

Thats's really nice, what Guarder kit did you use and did have to do any modifications?

Thank you.

this kit - 

View attachment 137891

minor fettling , the only “modification” for these is the BBU unit , but it’s all very simple and straight forward . Other than that , just take your time , give everything a good grease then run it in

 

[Nick G]

Added a small red dot to the GBB SD . Put a few mags through it yesterday and it shoots very nicely. Only did a rough hop set , but there is plenty of adjustment left so I can obviously go heavier than the .30's I run in all my GBB kit.

Chronod it , and it was a tad 'warm' that was outside with a mag that had been used once and refilled so the mag was cold and with red gas.

Fitted a spare restrictor disk that was in the draw and it was then at .90 j in a cold garage on green gas. So should be nicely skirishable at that. A warm mag or red gas will pop it just over the 1.0j mark . It's basically doing the same figures as my MP7 , so happy with that. 

I plan to look at fitting a tracer unit into the front of the silencer, but will need to work out what length inner barrel I'll need as the existing one runs full length. That will be a project for over the winter, I'll run it as is for now.

Oh and ordered an AW drum mag for it from KY , will report on what that is like once it turnes up.

View attachment 137902

View attachment 137901

 

[Jez_Armstrong]

Added a small red dot to the GBB SD . Put a few mags through it yesterday and it shoots very nicely. Only did a rough hop set , but there is plenty of adjustment left so I can obviously go heavier than the .30's I run in all my GBB kit.

Chronod it , and it was a tad 'warm' that was outside with a mag that had been used once and refilled so the mag was cold and with red gas.

Fitted a spare restrictor disk that was in the draw and it was then at .90 j in a cold garage on green gas. So should be nicely skirishable at that. A warm mag or red gas will pop it just over the 1.0j mark . It's basically doing the same figures as my MP7 , so happy with that. 

I plan to look at fitting a tracer unit into the front of the silencer, but will need to work out what length inner barrel I'll need as the existing one runs full length. That will be a project for over the winter, I'll run it as is for now.

Oh and ordered an AW drum mag for it from KY , will report on what that is like once it turnes up.

View attachment 137902

View attachment 137901

Needs a torch setup ? I found this the other day and printed it, very handy 

View attachment 137906

 

[TrooperX]

21 hours ago, JimFromHorsham said:

this kit - 

View attachment 137891

minor fettling , the only “modification” for these is the BBU unit , but it’s all very simple and straight forward . Other than that , just take your time , give everything a good grease then run it in

Oh wow, that’s nice!  I’m very tempted now.

 

[pyromancer6]

A2 stock arrived today - which means I can finally run the torch frontend & actually plug a battery in at the same time, which is nice. Have a clone C-More railway coming in soon which'll probably go on this if it suits it enough, alongside one of those abhorrent modern cocking handles because the proper ones won't be in stock until next year [according to an email I sent airsoftpro.cz, we'll see] and adjusting the hop without being able to lock the bolt to the rear is a massive pain in the ass lol

Also got a forward assist & replacement bipod for the SR-25 too.

 

 

[TheFull9]

Given me the kick up the rear I needed to finally get around to buying red and blue tape for my MP5 mags, thanks mate.

 

[Skara]

Decided to swap handguards between the 7" M4 and the 9mm PDW, now they colour match a litlle better with the rest of the components.

Also a little sneak peek into the PDW's gearbox..

W - - ?level over 9000 as @Rogerborgonce said...

 

[Jez_Armstrong]

Making the Bow GBB MP5k stock fit an AEG is definitely a 2/10 would not do again but over the moon with the results

View attachment 138137

View attachment 138138

 

[Enid_Puceflange]

Happy with my little add ons to the gen5

Angrygun MOS plate to accept clone ACRO

Clone TLR-1

Pro Arms steel Supressor sights which I surprisingly managed to “white dot” without too much of a mess despite being a tad shakey. 

View attachment 138148
 

View attachment 138149

View attachment 138150

 

[Diablo675!]

Gbb mws

2 systema PTWs 

too many trick and RS parts to list 

View attachment 138218

 

[mightyjebus]

Star L1A1 with EnglishKiwi 3D printed (SLS) L2A2. Gave the L2 a lick of paint, a couple of labels and a bit of weathering to make it seem a bit aged.

View attachment 138388

View attachment 138389

 

[ButcherBill]

I'm a sucker for an SLR

 

[Wooly57]

Here’s a pic of my CQBR modded up ?? all black erereerythaang ???

View attachment 138482

 

[JinxDuh]

Here’s a pic of my CQBR modded up ?? all black erereerythaang ???

View attachment 138479

So black, the entire image is black.

 

[Wooly57]

So black, the entire image is black.

That’s how we do it ? ninja ? 

I have no clue why it’s uploaded as a black image and why when I edit it.. re upload.. it’s still black ?

FML ?

 

[JinxDuh]

That’s how we do it ? ninja ? 

I have no clue why it’s uploaded as a black image and why when I edit it.. re upload.. it’s still black ?

FML ?

It’s showing now haha

 

[pyromancer6]

WADSN X300U arrived today alongside a CO2 mag with the cool baseplates, so I took a few neat pictures.

Just need to cough up the pennies to send the slide & frame off to West Laser to get engraved and cerakoted and it'll be pretty much done aethestics-wise.