• Hi Guest. Welcome to the new forums. All of your posts and personal messages have been migrated. Attachments (i.e. images) and The (Old) Classifieds have been wiped.

    The old forums will be available for a couple of weeks should you wish to grab old images or classifieds listings content. Go Here

    If you have any issues please post about them in the Forum Feedback thread: Go Here

Gun picture thread

Voodoo. said:
View attachment 77650

My Umarex HK416A5 w/ suppressor, angled foregrip, PEQ-15, 5mm polycarbonate sight protector, Feyachi RDS-25, Vector Optics 5x flip-to-side Magnifier, PTS EPM Mag and genuine Magpul MOE Stock. Also using a Viper Tactical VX Sling. Got somerubber rail protectors, to make it more comfortable to hold. The internals were upgraded primarily for longevity, with a new inner barrel for a slight range boost. Here are my upgrades:

ORGA LEX05 6.05mm inner barrel – 275mm
Prometheus Air Seal Chamber Packing – Soft
Firefly Namazu Flat Hop – Hard
Air Pad v2/v3 3/16” 70D

I also cleaned up and shimmed the gearbox. Fair to say I'm happy with it!
Click to expand...
Nice build buddy, how you finding the magnifier? I tried running one at one point in time but didn’t get on too well with it, I found there was too much wobble so couldn’t really hold zero all too well 

 
Joe142 said:
Nice build buddy, how you finding the magnifier? I tried running one at one point in time but didn’t get on too well with it, I found there was too much wobble so couldn’t really hold zero all too well 
Click to expand...
My rds' riser is slightly too tall for the rds to be perfectly level with the magnifier, so I've ordered a slightly shorter one in the meantime. As for holding a zero, it's held up surprisingly well. I had to adjust the magnifier so that the rds' reticle was in the centre of the optic, and it's been fine since then. Both the red dot and the magnifier is rated for actual firearms, so it's very nice.

 
Voodoo. said:
My rds' riser is slightly too tall for the rds to be perfectly level with the magnifier, so I've ordered a slightly shorter one in the meantime. As for holding a zero, it's held up surprisingly well. I had to adjust the magnifier so that the rds' reticle was in the centre of the optic, and it's been fine since then. Both the red dot and the magnifier is rated for actual firearms, so it's very nice.
Click to expand...
You’ll have to post a pic when the new riser comes in id love to see it, what are the optics you are using? Ive tried the repro G33 and vortex optic but didn’t really get on too well with it 

 
This little puppy is back with me after some extensive work. Will likely swap out the B19 for a B19N at some point simply because I think they look nicer, and likely swap the grip/handstop to an RK-6. Will be adding paracord to the stock and I think it’s about there.

View attachment 77715

View attachment 77698 

 
Last edited by a moderator:
This is my Viper Tech 2021 production KAC SR-16E3 Mod 1 GBBR.

6061 T6 receiver, produced with URX 3 handguard.
Larue Tactical rail clips, Hogue ar15 pistol grip
Installed the KAC handguard cover.

bd0f841b3b59ede3c8bec21906d08142298272a1f8ddd7677c15892c7fcdee9a.jpg


dc2e07f74d9cb353d64475b3ea7fa24f80f726d30859ed33c5eed8129d8d8bc3.png


71cd353f238bb02c5db746c73ee4acc9d604ddb289332a69254362917d266a83.jpg


A mount from Geissele arrived at my house today and I installed my LPVO.

 
Last edited by a moderator:
/Almost/ finished my custom ICS BCM Hera Arms CQR:

Q4lYDJx.jpg


I'm getting fancy takedown pins, forward assist, dust cover, trigger guard, getting the mags cerakoted the same colour but leaving the baseplates black, should look good.

I've got a black NGAL and one of the new MAWLs on the way, don't know which I'll end up using.

Any suggestions for a sling for this? I am thinking maybe a single-point attached to the stock, P90 style?

Also finally my PTS ACR stock got off the boat after 3 long months, I loosely slapped the gun together for a pic:

F281ofi.jpg


Just waiting on a Warhead motor for this and I can put it together. I am getting a black Wilcox mount to swap that with, and might swap to a MAWL on this too depending on how I like the look.

 
Well, a lot of work later and shes finished. HPA'd STAR L86. R-hopped 550mm IB, Polarstar F2 engine inside a custom designed and 3D printed gearbox, custom wiring and microswitches, modifications done to fit the IGL, and more. Max range about 85m (not accurate range for you haters). Im happy. Still need to sort out the two side pins behind the magwell, look into adding a grip of some sort if needed, and toss a light on it.

View attachment 77787

 
You must log in or register to reply here.

Similar threads

andersson
G&G L85a2 upper receiver jumps out of alignment
Replies
1
Views
237
ButcherBill
ButcherBill
S
VFC BCM MCMR GBBR and VFC PRO FORCE Sig MCX
Replies
0
Views
491
StayOnTarget
S
Zarrin
Asian retailer Checkout w/ over 50% of RIF externals
Replies
5
Views
1K
Bnjemann
Bnjemann
Dogsbody100
Upgrading a Well MB 01
Replies
3
Views
645
Rogerborg
Rogerborg
sam_91
Hey All , new to this forums but not new to Airsoft
Replies
1
Views
925
ButcherBill
ButcherBill
Back
Top