Pollynator_bravo2

Ok cheers for this. I think it’s the nub position most probably. It had a half job done on it which I’ve just discovered. It looks like an omega nub is in but not a maple bucking

Evening all ive found that my bbs are curving right. What could cause this please ?

Brilliant - thanks for this

Hey folks - what size should the O ring be for a standard aeg m4 piston in a V2 box ?

So of the the things. The gear box was to tight which I think basically means is that the tappet plate needs sanding a bit. As soon as I took the tension off the nozzle came forward. Thanks to everyone who gave advice. Always much appreciated

Thank you. I’ve not had chance to take it apart again but I hope to before the weekend

No it’s some glue but I’m wondering if that is putting pressure somewhere. I’ll investigate tomorrow for sure

So this is what’s happening in a picture. The nozzle is finishing here. I noticed when it was apart some odd west marks on the underside on the nozzle. Could this be misalignment? Just looking for ideas so I can eliminate possible causes. I’ve got some slow mo video but it’s blurry and I need to trim it Slow mo video. Sorry about the quality IMG_8837.MOV

Ok thought as much. Next job is to figure out why. I’ll try and share pictures later

I have noticed the nozzle is stopping before the hop leaving a few millimetres of gap is this normal ?

?‍♂️ so after putting the old cylinder back, getting the pinion into the correct place………. We are now firing at 136fps and not at all when the hop is even slightly turned up. However I can feel a good air flow through the end of the barrel. mom guessing it’s not sealing to the hop/bucking very well. The only thing that wasn’t changed was the nozzle, bucking, hop, and barrel

So when I opened her up I found a couple of points. When the piston pulled back it on just exposed a tiny bit of the bottom of the tear drop cut out so it’s not getting much air in so to speak. The noise looks to be the pinion running on the wire retainer in the housing. got most of it reset only to repeat the fun of getting the spring loaded trigger and anti reversal latch back. I did buy some holders for them but they have disappeared so it’s waiting for more to be delivered. thanks for the help everyone

Ok thanks for this. I’ll look at the old parts I’ve got as I think possibly the previous one may have been 3/4. If not I’ll swap it out.

Thanks for the help on this one. I did the upgrade and it worked spot on !!!!

Fits perfect tbh sorry. The barrel length is 240 mm. I’m wondering if it’s the wrong size cylinder now. I’ve had it all open and everything is free moving. I like to learn as it’s fun doing tech stuff but if I don’t figure it then it’s off to a tech I’ll go

Gate had a sale early in the year on their own website. Plus I brought in the polish currency which was very favourable so I didn’t pay anywhere near the cost if I’d of brought in the Uk. I will open her up this weekend and see if I can see what’s going down I have the eon cnc gear box now so no longer have the nuprol one

So the list of bits are as follows: Gate EON V2 gear box Titan Expert ASG Infinity U-18000 motor 8mm Ceramic bearings 13:1 Cyma gears EON tappet plate Eon protector cylinder head eon power hybrid piston head M105 Spring unfortunately I can’t find the details on the cylinder

Not checked so I’ll do that ? Previously it fired at 310 fps. I’m not sure what the stock size spring and gears were but they were as brought Thanks for that. Good shout I’ll give it a go Thanks. What does this look like when it binds and what should I check when investigating ? I can also add that it started to drop range when it had been used for the second half of a game. After about 15/20 mins of play.

Evening folks so I’ve popped a Titan ETU, m100 spring, eon gear box, eon piston and head, 13:1 gears, asg infinity 18000, into my nuprol defender. The fps looks a lot lower than I was expecting so I think I’ve screwed something up. The gate app isn’t picking anything out as a problem but it looks like I’ve missed what ever I’ve done wrong. Any help would be appreci IMG_8684.MOV IMG_8684.MOV ated IMG_8685.MOV Also it’s on a 7.4v lipo

IMAX B6 was the charger I was using. It was a stick 11.1v lipo I can’t remember the mah but think it was 1400 possibly

Hey folks. So after having a battery go nice and crispy on what I thought was a top notch lipo smart balance charger I’ve left myself short of confidence in knowing good from bad. can someone suggest a good balance charger and where to get said item from. Also some tutorials on how to use them properly would be amazing ?

Your an absolute legend. Huge thanks !!!! Just a quick question last one I promise lol. What should my other items be on the conversion shopping list? I guess a air tank and line would be a couple of things and a regulator?

Hey - I’ve got a Double Eagle pump action shotgun currently running on green gas. The buffer tube is where the valve is for topping up the reservoir. I want to upgrade to HPA but everywhere asks if it’s WE/TM/KWA which fittings should I go for guys as I’m stuck??

Thanks everyone. Now it’s time to spend haha

Evening all whats the best bb in terms of brand and reliability currently. I’ve been using Valkyrie but they don’t have what I want currently. Ideally bulk discount as ill being buying a lot