[Tippmann M4 V2 custom outer barrel]

Tippmann M4 V1/V2 OUTER BARREL - Custom Sizes Available - 14mm CCW - TA50006 | eBay

Just literally seen this on ebay, 3d printed but maybe it'd be ok.

[Tippmann M4 owners thread]

you might find a standard bore barrel a good start, might alleviate some of your fps inconsistences, also may solve your hop rubber issue. worth a punt to rule out the tight barrel.

 

[Tippmann M4 owners thread]

I had the nozzle for sale but removed the advert, I have a few other bits and was going to put it up as a set, does your v1 have either the hard recoil buffer spacer fitted ? or the dave air saving device ? if either of these are fitted its best to remove them and start afresh. This will make dialling in your fps a lot easier.

what barrel is in it ? I had a pair of madbull blue shark hop rubbers that actually worked fantastic in mine and they were cheap, hopped .3 no issue. Although the macron yellow should also be fine. Its easier to cut the end off the hop feed lips if you feel the nozzle is ruining them. 

Depending on who did the dwell mod you can put a bit of grease around the screw to stop leaks.

Also pay close attention to your hop unit, I assume its a replacement tdc job, may be worth pulling it out and checking it over.

also check the feeding manually to make sure there isn't to much resistance for the bolt when loading a round.  

 

[RtX 3070]

On a whim at 17.35 on the 2nd I placed a pre order with scan for a 3070 and blow me down its out for delivery tomoz, that was unexpected

 

[Swapping From Nimh to Li-po Batteries for Umarex Ump Sportline]

ASG 7.4V 1300 mAh Lipo Battery – Stick Type Tamiya connector is what i use in my ump, fits perfectly.

[Western Arms Parts Advice]

4 hours ago, hitmanNo2 said:

As you suspect, it looks like a Wilson Combat Striker.  But in a Kimber SWAT TLEII box which is quite odd.  Is this the same box it came with?

 

https://sqr.militaryblog.jp/e944130.html

 

KJW have made compatible hop and BBUs that work in WAs but I'm not sure exactly which one you'd need.

 

Unfortunately front sight sizes vary.  Probably easiest to try some for TM hicappas and mod the sight to fit.

On a side note, does anyone still make replacement valves for the mags ? I have only found one place that does gaurder replacements but the shipping is £25 for a £8 part.

[Rip Combat South Woodland]

5 hours ago, Hatchet said:

We took the fort down yesterday. Just a big empty space there now, very strange. Front bridge and tower at the village is gone, Wendy house gone. The village mostly still stands, but I expect that will be another day's work.

 

Having played there for around 20 years, I can't express quite how gutted I am by the loss of the site. This year has been... sub-optimal.

 

Still, the one thing I do have confidence in is the CS staff. A new site is a question of when, not if. Can't say I'm going to enjoy the wait, but maybe it's time to visit some other sites in the meantime.

Many a great day at combat south over the years!!!!

[Old School Airsofters.]

Snap, loved a bit of Stargate back then and there was no marui version, has a ver 3 box with the motor mounted horizontaly under the cylinder. I'll dig it out and take some pics for perpertuity lol

[Old School Airsofters.]

On 14/07/2020 at 09:56, Speedbird_666 said:

Late '90s/early '00s - staring at the DenTrinity website - they had built a P90 (which was uber cool in popular culture at the time) using TM internals in a model gun way before TM bought theirs to market.

 

I was hooked from there on in.

I still own this p90, the plastic has not aged well, was made from an old toytec version that Den had butchered, only issue was having to have a battery bag strapped to the side.