What have you made?

[Rogerborg]

Found a couple offcuts of 0.9mm Ti sheet and bolted my face mesh to my Bolle X800’s ?

Nice, what's the hole size on that mesh?

 

[Davegolf]

The goggs or the mask?

 

[Davegolf]

The Goggs are mesh supplied by @heroshark, his super fandango hexagonal stuff.

Did some drill today with the mask, tweaked it about - all good.

Rivetted the lower and painted it up

Definitely the best setup I’ve ever had, with prescription inserts in the X800s

View attachment 92336

View attachment 92337

 

[Dan Robinson]

Why sir, you appear to be pointing at the ground. 

 

[Rogerborg]

The Goggs are mesh supplied by @heroshark, his super fandango hexagonal stuff.

Ah, right, you have chosen wisely. I've gone mesh outdoors now, it's so liberating not to have the worry about fogging.

 

[Davegolf]

Aye fog is the biggest bitch of airsoft, especially if your eyes need correction.

 

[Stratton Oakmont]

I am a child

View attachment 92348

 

[PureSilver]

Inspired by the Springfield V12s, I present the Detonics... V6? This is eventually going to be mocked up (with further inspiration from Marui’s Vorpal Bunny) with smoothed grips, a front rail, and a battleship grey paintjob.

It is an ARMY R45 with an ACM Shield RMS, a Nova trigger, and Shooters Design 150% recoil springs. Not pictured yet are the Army extended magazine release and modified grips, which have been filled with putty in readiness for relief cuts and sanded smooth.

Milling the slide and the adaptor plate allowed me to sink the optic 3.5mm into the slide. This actually lower-third-cowitnesses with the factory sights, somehow.

Custom milled and drilled slide and barrel ports. The ARMY’s outer barrel is stainless steel and broke one of my milling bits. Lesson learned about using them to drill holes...

Total cost so far: ~£120

 

[Stratton Oakmont]

Inspired by the Springfield V12s, I present the Detonics... V6? This is eventually going to be mocked up (with further inspiration from Marui’s Vorpal Bunny) with smoothed grips, a front rail, and a battleship grey paintjob.

​

It is an ARMY R45 with an ACM Shield RMS, a Nova trigger, and Shooters Design 150% recoil springs. Not pictured yet are the Army extended magazine release and modified grips, which have been filled with putty in readiness for relief cuts and sanded smooth.

​

Milling the slide and the adaptor plate allowed me to sink the optic 3.5mm into the slide. This actually lower-third-cowitnesses with the factory sights, somehow.

​

Custom milled and drilled slide and barrel ports. The ARMY’s outer barrel is stainless steel and broke one of my milling bits. Lesson learned about using them to drill holes...

​

Total cost so far: ~£120

Is that honestly a genuine shield???

 

[Lozart]

 with an ACM Shield RMS

Is that honestly a genuine shield???

Genuine Chinese copy!

 

[PureSilver]

Is that honestly a genuine shield???

Fake as fake can be!

 

[Stratton Oakmont]

Is it any good?

 

[PureSilver]

Is it any good?

I don’t have many rounds through it; it’s solely for this pistol, and the pistol isn’t finished. From what limited handling it’s had it seems perfectly OK; for what I paid that’s excellent.

 

[Druid799]

I am a child

AND ???? The problem is what ? ?

?????

 

[Floperator]

Too hot for client work, not too hot to dick about with my own little projects.

Today I made a packing piece out of brass plate for my FNX,  to go around those awkward exposed tabs:

View attachment 93615View attachment 93616View attachment 93617View attachment 93618View attachment 93619

 

[SBoardley]

Rs magpul Emags for my TM ngrs. 

View attachment 93865

View attachment 93866

 

[TheFull9]

You do the mods or pay someone?  I bought some EMAGs yeeeears ago to do the exact same, have lots of TM standard 82/30 USGI mags sitting around, but never managed to combine the two.

 

[SBoardley]

You do the mods or pay someone?  I bought some EMAGs yeeeears ago to do the exact same, have lots of TM standard 82/30 USGI mags sitting around, but never managed to combine the two.

Yeah I’ve just done 4 for tm. Tbh bud, the best doner mags are epm. I can show you how to do them in like 10 minutes. The old stanags have a lot of tedious work. You can do the epm mod with a file , a sliding square and hack saw. No power file needed. 

View attachment 93920

 

[SBoardley]

You do the mods or pay someone?  I bought some EMAGs yeeeears ago to do the exact same, have lots of TM standard 82/30 USGI mags sitting around, but never managed to combine the two.

I’ll try put how to footage up this weekend; I’ve got one more epm mag so I can do it completely from scratch. 

 

[RostokMcSpoons]

View attachment 94235
 

Rattle can 'MTP' on my olive green mag pouches...   it's such an easy thing to do, but very satisfying for the 20 minutes it took