• Hi Guest. Welcome to the new forums. All of your posts and personal messages have been migrated. Attachments (i.e. images) and The (Old) Classifieds have been wiped.

    The old forums will be available for a couple of weeks should you wish to grab old images or classifieds listings content. Go Here

    If you have any issues please post about them in the Forum Feedback thread: Go Here

Gun picture thread

Last edited by a moderator:
The remaining guns that need testing and tweaking while I'm not allowed to play. Most are simple tests and tweaking, nothing major since I finally got the MWS hopping the ammo I want to put through it last Sunday. It's mostly just setting the hop for the weights I want to use, but a few other minor tweaks needed.

From left to right:

TM MWS w/ Modelworks mk12 kit - Need to make sure it's shooting straight. Scope I had on it was wonky because of the mounts on Sunday

Tanaka m700 w/ real Remington stock - Installed a new hop rubber and nub as it was a bit crap before. Need to set the hop now with the new setup

JG BAR-10 - Just need to find what psi to set for 1.1J so I can use it at night games / no MED games; disgustingly quiet since it's internally suppressed and half of that outer barrel is just alternating large/small foam baffles. Already know it shoots phenomenally at 155psi, which gives about 2.3J on .48s, and I can go as low as 80psi, so sure I can get it to 1.1J as well

G&P m14 DMR - Ironically not a DMR. Wasn't hopping well, but power, noise and snappiness was all amazing, so installed a new MR hop rubber. Need to set the hop up now.

KJW m700 - Usually has a suppressor on it! Finally got around to finishing this one with the threaded shorter outer barrel, as well as the AA hop unit, nub and flamingo rubber. Need to set it up, both power and hop up.

I think I have a type... ?

View attachment 133401

 
Last edited by a moderator:
Impulse said:
The remaining guns that need testing and tweaking while I'm not allowed to play. Most are simple tests and tweaking, nothing major since I finally got the MWS hopping the ammo I want to put through it last Sunday. It's mostly just setting the hop for the weights I want to use, but a few other minor tweaks needed.

From left to right:

TM MWS w/ Modelworks mk12 kit - Need to make sure it's shooting straight. Scope I had on it was wonky because of the mounts on Sunday

Tanaka m700 w/ real Remington stock - Installed a new hop rubber and nub as it was a bit crap before. Need to set the hop now with the new setup

JG BAR-10 - Just need to find what psi to set for 1.1J so I can use it at night games / no MED games; disgustingly quiet since it's internally suppressed and half of that outer barrel is just alternating large/small foam baffles. Already know it shoots phenomenally at 155psi, which gives about 2.3J on .48s, and I can go as low as 80psi, so sure I can get it to 1.1J as well

G&P m14 DMR - Ironically not a DMR. Wasn't hopping well, but power, noise and snappiness was all amazing, so installed a new MR hop rubber. Need to set the hop up now.

KJW m700 - Usually has a suppressor on it! Finally got around to finishing this one with the threaded shorter outer barrel, as well as the AA hop unit, nub and flamingo rubber. Need to set it up, both power and hop up.

I think I have a type... ?

View attachment 133401
Click to expand...


Seems your type is long and slender, nice long range rack you have :). 

 
Only playing mate, I know not to pick on a giraffe… holo would look much better.

I’d get some sling silencers and maybe move your dual switch if you can, that cable looks a little taught / snaggy.

 
Wavey_Gravey said:
Only playing mate, I know not to pick on a giraffe… holo would look much better.

I’d get some sling silencers and maybe move your dual switch if you can, that cable looks a little taught / snaggy.
Click to expand...
i know ?. Think I’ll have to order one. I might have to I usually switch to 1 point when playing. 
 

yeh wish the cable was longer but the switch is in a nice place for my hand haha 

 
A good few hours with the dremel and it’s “almost” a perfect fit

Fitted one of these to my M4 a couple of years ago and much prefer the angle for comfort. 
The standard 553’s grip is ok, but looks “meh”

So got a MOE-K2 AK version for SIG

Looks miles better imo

Before:

 View attachment 133969
 

After:

View attachment 133970

 
You must log in or register to reply here.

Similar threads

andersson
G&G L85a2 upper receiver jumps out of alignment
Replies
1
Views
236
ButcherBill
ButcherBill
S
VFC BCM MCMR GBBR and VFC PRO FORCE Sig MCX
Replies
0
Views
490
StayOnTarget
S
Zarrin
Asian retailer Checkout w/ over 50% of RIF externals
Replies
5
Views
1K
Bnjemann
Bnjemann
Dogsbody100
Upgrading a Well MB 01
Replies
3
Views
644
Rogerborg
Rogerborg
sam_91
Hey All , new to this forums but not new to Airsoft
Replies
1
Views
924
ButcherBill
ButcherBill
Back
Top