Bought one the weekend with bipod , scope etc just to see how I get on , using .30g bbs and even at 20 Mtrs it seems terrible shooting bbs all over the place , just stuck a tomato up at the Range to zero in the scopes theta optics and it’s hit and miss are theses sniper rifles that bad ?
-
Hi Guest. Welcome to the new forums. All of your posts and personal messages have been migrated. Attachments (i.e. images) and The (Old) Classifieds have been wiped.
The old forums will be available for a couple of weeks should you wish to grab old images or classifieds listings content. Go Here
If you have any issues please post about them in the Forum Feedback thread: Go Here
Cyma cm708
- Thread starter Simonwwfc
- Start date
Lozart
Supporters
- Jun 24, 2013
- 8,493
- 4,941
No, but apart from some limited, specific examples I can't think of many bolties that are accurate out of the box.
RostokMcSpoons
Members
- Sep 3, 2021
- 1,940
- 1,749
I just bought a cheapo sniper rifle too, just to dip a toe in the water...
I bought some Geoff's .40s and the gun shoots quite nicely. But it's inconsistent. I'll get 3 shots looking bang-on, but then I'll get one or two off to the right - either going straight right or curving off a bit. At 15m I think might be missing by 4 or 5 inches - I'll stick a paper target up and measure it properly.
The barrel looks clean all the way through.
I'm guessing that sort of behaviour warrants a new hop rubber and nub as a starting point... but I'm also aware it might be the start of a long and expensive journey, so I've resolved to leave it alone until I can test it at greater range and put a decent number of shots through it.
Edit: a very quick string of 6 shots.. 1 flier, low-left, the rest in a 1.75" group - which goes to show that shots may look worse through the scope than they actually are...! I did dial in some more hop after a few warm-up shots away from the target, so perhaps my previous shots weren't back-spinning enough to stabilise them properly?
I bought some Geoff's .40s and the gun shoots quite nicely. But it's inconsistent. I'll get 3 shots looking bang-on, but then I'll get one or two off to the right - either going straight right or curving off a bit. At 15m I think might be missing by 4 or 5 inches - I'll stick a paper target up and measure it properly.
The barrel looks clean all the way through.
I'm guessing that sort of behaviour warrants a new hop rubber and nub as a starting point... but I'm also aware it might be the start of a long and expensive journey, so I've resolved to leave it alone until I can test it at greater range and put a decent number of shots through it.
Edit: a very quick string of 6 shots.. 1 flier, low-left, the rest in a 1.75" group - which goes to show that shots may look worse through the scope than they actually are...! I did dial in some more hop after a few warm-up shots away from the target, so perhaps my previous shots weren't back-spinning enough to stabilise them properly?
Last edited by a moderator:
Tactical Pith Helmet
AF-UK patch owner
- Jul 5, 2016
- 1,040
- 2,576
By the time it shoots nicely, it will be an expensive sniper rifle...
Rogerborg
Supporters
- Aug 22, 2017
- 9,190
- 6,048
Nah, you only need to change the hop rubber. And arm. And unit. And barrel. And add spacers. And change the spring. And piston. And guide. And trigger unit.
Once you've spent another £300 on it to replace every single internal part, it'll be fine...
It's an airsoft truism that all decent bolt actions are built, not bought, but my Silverback TAC-41 says otherwise.
Last edited by a moderator:
Lozart
Supporters
- Jun 24, 2013
- 8,493
- 4,941
...and that right there is one of the limited, specific examples I was on about!
Rogerborg
Supporters
- Aug 22, 2017
- 9,190
- 6,048
Caveated that with airsoft quality control, nothing is guaranteed. It's just more likely that you'll get a good, usable example of a Silverback or (gritted teeth) SSG-10 than a cheap JG or CYMA. Steyr Scout is also getting some love.
Similar threads
