Changing out the handguard on a CM16 Mod 0

G

Gepard

Supporters
Joined
Sep 21, 2017
Messages
1,443
Reaction score
194
So I've had this gun for a while now and want to change things up a bit. It's front wired so the battery is stored in the handguard. 

I'd like to swap the magpul style handguard for a rail system but need a place for the battery to go

I'm no techie, so rewiring is not an option for me. I've heard that you can buy PEQ boxes and store the batteries in there, but haven't looked into it. 

What are my options?

 
Gepard said:
So I've had this gun for a while now and want to change things up a bit. It's front wired so the battery is stored in the handguard. 

I'd like to swap the magpul style handguard for a rail system but need a place for the battery to go

I'm no techie, so rewiring is not an option for me. I've heard that you can buy PEQ boxes and store the batteries in there, but haven't looked into it. 

What are my options?
Click to expand...
Click to shrink...


If by "Magpul style" you mean an MOE clone, then the battery can stay put. Plenty of space in there!

 
How would a PEQ box work? I assume it's just a compartment to store the battery but what types does it take?

What about the wiring? As you can see from this photo it extends into the handguard itself so I'm wondering how I can manage the cables. 

View attachment 30241

On top of that from the little information I could find on this topic the actual handguard is shorter than that on the market. Would I be able to move the gas block closer to the receiver? 

 
Gepard said:
How would a PEQ box work? I assume it's just a compartment to store the battery but what types does it take?

What about the wiring? As you can see from this photo it extends into the handguard itself so I'm wondering how I can manage the cables. 

View attachment 30241

On top of that from the little information I could find on this topic the actual handguard is shorter than that on the market. Would I be able to move the gas block closer to the receiver? 
Click to expand...
Click to shrink...


Right, first off I thought you were replacing a railed handguard with a Magpul style one so apologies for that!

Anyway, you can route the cables out through one of the holes in the handguard and into the back of the PEQ battery box (they usually have a little hole at the back so as to not be obvious. They usually hold something like a 1200mAh square type battery (LiPo that is) but some come with an extension that will allow longer batteries. The trick would be to pick the right model of PEQ for your battery - a PEQ15 will hold a small square battery but a PEQ2 will hold a longer NiMh style one eg: https://www.amazon.co.uk/Airsoft-Wargame-Tactical-D-Boys-Battery/dp/B00RN0KP2S/ref=pd_lpo_sbs_200_t_0?_encoding=UTF8&psc=1&refRID=HRJE1PZDM5W4KM4B332A

 
Last edited by a moderator:
Lozart said:
The pictures on this show the extension and the hole in the back for wiring https://www.amazon.co.uk/FMA-Airsoft-Dummy-Battery-Mounting/dp/B015D1DGLK/ref=cts_sp_1_vtp
Click to expand...
Click to shrink...


That's great, thanks. I see how it works now. 

Do you have any handguards you would recommend? Preferably a RIS Rail. I think I might need to move the shroud and gas block as the handguard looks like it's a little longer than carbine length but I'm sure I can figure it out. 

 
Gepard said:
That's great, thanks. I see how it works now. 

Do you have any handguards you would recommend? Preferably a RIS Rail. I think I might need to move the shroud and gas block as the handguard looks like it's a little longer than carbine length but I'm sure I can figure it out. 
Click to expand...
Click to shrink...


Depends on what style you want. If the original guard is more than 7" then the drop in RIS units won't fit (and you'll probably need an end cap too). Measure up the length you need and decide what style you like - RIS/RAS/Keymod/M-Lok - and go from there.

 
Lozart said:
Depends on what style you want. If the original guard is more than 7" then the drop in RIS units won't fit (and you'll probably need an end cap too). Measure up the length you need and decide what style you like - RIS/RAS/Keymod/M-Lok - and go from there.
Click to expand...
Click to shrink...


I just took apart the reciever and had a little nosey around whilst I was at it and my gun doesn't have any threads for a rail system and I don't know how to take off the gas block. God I'm such a noob. 

Am I missing something obvious here? I don't think I've ever opened it up before so this is all new to me. 

 
Last edited by a moderator:
Gepard said:
I just took apart the reciever and had a little nosey around whilst I was at it and my gun doesn't have any threads for a rail system and I don't know how to take off the gas block. God I'm such a noob. 

Am I missing something obvious here? I don't think I've ever opened it up before so this is all new to me. 
Click to expand...
Click to shrink...


The thread for attaching a rail is under the delta nut (the bit you pull back to release the current handguard). You'll need a pin spanner or an armourers wrench to get it off.

 
To get the delta off with out a wrench or AR tool you can (once the A sight + cap is removed) use the larger of the two halfs of a handguard to undo it. Just use it as a wrench by putting it back on the teeth of the ring, keep it straight as if mounted and turn. Works for me :)

 
I'll give it a shot tomorrow. Thanks chaps. Any suggestions for the gas block? I had a look online but the pins are different to the other CM16s. 

Gave it a few taps with a hammer and a small screwdriver just to be sure but no such luck. The pins didn't budge.

edit: I measured the length of G&Gs handguard and have come to the conclusion that is is rifle length and not carbine length. 

I will need to move the gas block and end cap closer to the receiver in order to fit a carbine length handguard. 

I never knew replacing a handguard could get so complicated! 

 
Last edited by a moderator:
You'll have to hit the pins quite hard from left to right if the gas block is pinned in the normal manner. There's normally a grubscrew under where the sling loop would go, two pins holding it straight on the barrel and sometimes another pin locking the gas tube in position too.

Make sure you support and rest the block and barrel on something to stop it moving when you hit it. Previously I've used a bit of mdf to hammer against as it's soft and will catch the pins if over punched.

The trouble that may occur moving the A-sight gas block is that the barrel often has two grooves milled out for the pins to slip across and keep the A-sight level and aligned. If you move it back and forth there won't be any grooves to pin and the A-sight will flip round the barrel at will. It may be possible to secure it with just the grub screw but if it takes a knock it'll move, potentially bending the gas tube with it. It's not an issue with a low profile gas block + floating handguard but if you're keeping the A-sight + cap then it's something to consider.

 
Are you sure the gas block will move.  I thought those on the CM16 were moulded in, so cannot be removed.

 
The CM16 Mod 0 handguard is about 1/4" shorter than a rifle length one. If moving the gas block is proving to be an issue, you could change the outer barrel completely for not a lot of cash (CYMA M4A1 barrels are only around £12 online) which would then free you up to use whatever handguard you like!

 
Lozart said:
The CM16 Mod 0 handguard is about 1/4" shorter than a rifle length one. If moving the gas block is proving to be an issue, you could change the outer barrel completely for not a lot of cash (CYMA M4A1 barrels are only around £12 online) which would then free you up to use whatever handguard you like!
Click to expand...
Click to shrink...


Ah! That simplifies things. Are there any websites with this pricing you'd recommend buying from? My usuals are almost double the price! 

 
Gepard said:
Ah! That simplifies things. Are there any websites with this pricing you'd recommend buying from? My usuals are almost double the price! 
Click to expand...
Click to shrink...


Seems my costing may be a bit out of date - sorry.

Best bet is to have a look on AliExpress or ebay, plenty of chinese manufacturers making them.

 
Lozart said:
Seems my costing may be a bit out of date - sorry.

Best bet is to have a look on AliExpress or ebay, plenty of chinese manufacturers making them.
Click to expand...
Click to shrink...


It's the 10.5" outer barrel with the 4" extension you're referring to right? 

Also, removing the barrel itself seems to be causing a bit of a problem for me. 

View attachment 30333

The delta seems to be a different design to what @Immortalis referring to. I didn't need any tools to remove it.

 
Last edited by a moderator:
Hmmm.. that doesn't look like a normal Delta ring. Must be CYMAs own take on it.

 
You must log in or register to reply here.

Similar threads

A
Advice
2
Replies
21
Views
606
EvilMonkee
EvilMonkee
S
Evolution Airsoft
Replies
2
Views
805
Skara
Skara
Back
Top