What is your most highly upgraded gun?

[Mos]

List the model and the internals you've installed.

you can list the externals if you want, like rails, optics..

for me,

TM VSR-10 Pro,

Mancraft SDiK,

AA hop unit,

ML Autobot 60 deg w/ concave nub,

Large unnecessary scope that is slightly too big.

 

[PT247]

currently my VSR, but an upgraded VSR is not really much different from any other upgraded VSR.

Previously it was my KC-02, which internally was about as far as you could go and externally not far from it too:

3D printed VSR hop chamber and nub,

PDI 6.05mm inner barrel,

Nineball hop rubber,

CNC'd and hard anodised bolt, (I also had a 3D printed bolt too which was very fast cycling but not as consistent on fps),

CNC piston,

homemade barrel stabilisers,

shorty metal top rail,

hand carved wooden stock,

big f***ing scope.

 

[Hangtight]

Well MB 01

Prometheus EG 455mm barrel fitted with diy tape spacers.

AA hop up, EPDM R hop and eraser nub, Modify flat hop bucking.

Volume reduced Mancraft Sdik with diy flow reduction air nozzle.

Black steel cylinder.

Bolt handle machined and fitted with bronze bush to eliminate wobble on the end of the cylinder.

Trigger sears shaped and polished.

Palmer regulator and co2 cartridge adapter fitted inside the stock, adjustable though a small hole in the bottom of the grip. Adapter sited where the real steel monopod would be and accessible without dismantling anything.

Bipod adaptor removed and replaced with something a lot lighter.

Home made sun shade for the scope.

Stock smoothed and deseamed .

Diy Flecktarn paint.

Other stuff I've probably forgotten...

View attachment 22840

 

[Mos]

4 minutes ago, Hangtight said:Volume reduced Mancraft Sdik with diy flow reduction air nozzle.

Thats a pretty awesome looking rifle there,

I've just realized ive got a 

Cylinder:Barrel volume

          1   :  2

ratio, therefore I need to reduce volume in the barrel.

But why did you decrease the volume in the Mancraft cylinder? 

I thought it's best to have a higher cylinder volume to barrel volume?

 

[PT247]

Thats a pretty awesome looking rifle there,

I've just realized ive got a 

Cylinder:Barrel volume

          1   :  2

ratio, therefore I need to reduce volume in the barrel.

But why did you decrease the volume in the Mancraft cylinder? 

I thought it's best to have a higher cylinder volume to barrel volume?

Are you taking into consideration that CO2 expands? the volume in the cylinder will expand a hell of a lot, if it was air (spring) powered then you'd want them to match or have the cylinder slightly over volume, but you are using a pressurised gas so not the case.

 

[Mos]

Are you taking into consideration that CO2 expands? the volume in the cylinder will expand a hell of a lot, if it was air (spring) powered then you'd want them to match or have the cylinder slightly over volume, but you are using a pressurised gas so not the case.

Ah, thanks for the info.

imagined CO2 was like air in this scenario. Never mind, no need to freak out.

thanks for the info. All good stuff.

edit: This will also explain why you want to have good compression/air seals - you don't want to lose any of that precious air (or CO2.).

 

[Hangtight]

The Mancraft has more than enough cylinder volume for a 500mm barrel. Off the top of my head I think mine is reduced down to about 3.5cc,which requires a higher input pressure but allowing for the expansion of the gas still gives an effective cylinder volume of around 2.9x the barrel and hop. This ups the shot count to around 140+ shots per co2 cartridge, but the high initial pressure accelerates the BB though the hop so fast that it causes inconsistent hop issues. Hence the flow reducer in the nozzle. That is sized to give enough flow to still be accelerating the BB at the end of the barrel, but it also slows the initial acceleration. I lost count of how many times I took the damn thing apart while I was trying to figure that one out.

Just use it as it comes. You'll still get 70 shots per bulb, but if you get inconsistent hop then fit a flow reducer in the nozzle.

 

[jcheeseright]

Ooh, I do love a good dick waving competition. 

Systema PTW MAX2;

Internally - all boards waterproofed, Tac modded hop, shortened LiPo board, hop mod, KUMI 490 rewound motor.  

Externally;

RS Daniel Defense Mk18 RIS2

RS Daniel Defense QD sling receiver end plate 

RS Daniel Defense QD sling rail mount

RS Magpul CTR Stock & AFG2

RS Hogue rubber overmould grip

Holosun HS403GL 

RS Insight PEQ15 ATPIAL 

RS Surefire M600 on Haley Strategic thorntail 

RS Magpul trigger guard

Angrygun SOCOM Suppressor. 

All added up I'm in for just over £4,000 and it doesn't shoot significantly further than a G&G CM16. 

View attachment 22848

 

[djben9]

All added up I'm in for just over £4,000 and it doesn't shoot significantly further than a G&G CM16. 

very nice!!

if I spent that much though....id be either dead or divorced!!!!

all my 4 are basic hop rubber swap at moment. UK1RSR has a gate mosfet and locked to single shot. Awaiting upper receiver for spring upgrade for other sites though

as for add on's, they vary depending what I use and where but mainly front grip,  clone Eotech and Xcortech counter/tracer for most games and night/urban ones i'll add on a Torch / PEQ box.....all toys though

more billy basic

 

[sp00n]

(Will add pics when I get on my pc)

my vsr



mancraft kit

airsoft pro 90degree trigger

AA hop chamber 

maple leaf autobot bucking

pdi 430mm 6.05 barrel

pdi barrel stabiliser 1off 1/3rd of the way down the barrel

335mm light weight silencer

custom 3D printed top of barrel hop adjuster (not in pic)

custom made silencer adapter

custom 3D printed LRB kit

custom 3D printed silencer baffles (as quite as the g-spec silencer now)

cammo tape

jack pyke llcs leaves

4-16x50 mil dot scope (I don't remember the make)

my WE L86 (my baby and only the 4th known gbbr l86)



we l85a2

nuprol susat

ics l86 barrel (modded)

ics l86 barrel support and foregrip (modded)

ics l86 rear grip

ics l86 butt pad

custom 3D printed mid block securing block

custom 3D printed hop block adapter

custom 3D stainless steel printed barrel locating and retention insert

RA tech npas

 

[Sacarathe]

I changed the Grip on my G18.

 

[sokar666]

very nice!!

if I spent that much though....id be either dead or divorced!!!!

all my 4 are basic hop rubber swap at moment. UK1RSR has a gate mosfet and locked to single shot. Awaiting upper receiver for spring upgrade for other sites though

as for add on's, they vary depending what I use and where but mainly front grip,  clone Eotech and Xcortech counter/tracer for most games and night/urban ones i'll add on a Torch / PEQ box.....all toys though

more billy basic

That's basically what i'm doing to mine, different uppers for different scenarios

 

[djben9]

i see you have same CXP as me

my first baby!....haha

 

[sokar666]

i see you have same CXP as me

my first baby!....haha

Yeh first gun i ever got and never really used it as the scorpion is so good but i've decided to breath some life into it, upgrades, multiple uppers or different sizes and looks.