To be truely honest the 30k motor is not the be all & end all
if you want a 30k Krytac I have a used one if you like but imho a SHS Torque will match if not kick its ar$e to bits
The SHS Torque is one of best £ for £ motors you can get hold easily without breaking the bank
On a recent couple of builds I was finding these results upon final testing.....
Yes there are faster crazy motors out there that I can pull 33rps on 7.4v but they get warm even quite hot when caned a bit and current draw is quite a lot
The SHS Torque will rip say 27rps instead of 33rps on 12:1 gearing on 7.4v but runs cooler and draws 16/17amp instead of 24/26amps !!!
Wow - that is some draw which means your batteries are draining quicker for not a massive increase in rof
Not going into too much but still after short stroking, but using spacers to claw back lost fps using say a m110, you still get overspin above 30rps
and on 11.1v even with a bit of extra work she often will still double fire on fresh 11.1v even with SS & spacers
so for crazy speeds of 35+ m120/130 is going to be needed which also will reduce the initial rps anyway - so hence keeping her at up to 30rps is wise
there is little gained in going nutz above this imho - there is f*ck all to be gained - bollox to response n $hit
yes at 45rps but double firing and probably say 40rps max with m130 to get her to behave
but still little compared to gun shooting say 27rps over a stock 15rps
but 40rps n crap is not that FMF (F*ck Me Factor) over 27rps imho
Suffice to say after breaking stuff tooooooo many times I have come to conclusion to stay put into high 20's maybe nudge 30's but no more
Or 20's to mid 20's if doing a modest build without having to grind out for thick industrial wiring n crap struggling to squeeze it in pistol grip etc.....
The Torquey motors - and the SHS Torque is not a crazy frankentorque but a decent motor with a noticeable improvement over any stock motor
not too silly increase like 50% over ferrite but about 25% but also runs cooler and much less draw than the ultra whippy 14tpa speedy neo motors
The Krytac motors look like ferrite but are neodym even though they are black magnets, a vid is on youtube from ASTKillo or something about this
yes they look ferrite but in fact are a kind of neodym motor but not the usual insanely stronger chrome/silver type neodym magnets we often see
So yes the 30k is neodym but not that stronger neodym/earth magnets like SHS & others use.....
Hence the conclusion the 30k is not the be all and end all - is good but atm mine is replaced with a BD160 which clearly showed more response/rps
not sure if I'll replace it with 30k or a shs torque or leave it as is with a BD160 in there
I'm trying to resist the urge to rip her open inside - if it ain't broke... has never been yelling at me more so than with the krytac
But my honest opinion is that the 30k motor is not the holy grail or be all & end all that 20k owners may think imho
Maybe I should do more tests to determine the final results on 30k vs SHS Torque vs BD160 or crazy mofo's
but I didn't feel the FMF about the 30k motor tbh on 7.4v's compared to other stuff/motors
Other Krytac speed freak owners remember that the piston is likely to shred some of its plastic teeth if you go too crazy
which is a good design to prevent any PE smashing f*ck out of the rest of the box....
but please understand the risks of pushing ANY gun with mild UK springs in
so if you don't want to break your nice gun - even a Krytac resist the urge to take the pi$$ too much
they might be built very well but with regards to Pre Engagement as a very experienced tech mofo once said:
but a few like Krytac are working on stuff so with the mk2's it could be more:
