-
Hi Guest. Welcome to the new forums. All of your posts and personal messages have been migrated. Attachments (i.e. images) and The (Old) Classifieds have been wiped.
The old forums will be available for a couple of weeks should you wish to grab old images or classifieds listings content. Go Here
If you have any issues please post about them in the Forum Feedback thread: Go Here
Gate Titan V2
- Thread starter LordRonin
- Start date
ImTriggerHappy
Supporters
- Feb 25, 2015
- 5,374
- 2,228
Excellent bit of kit.
What do you want to know.
What do you want to know.
- Thread starter
- #3
just want to know any important things about installing and using. Maybe the best settings for a DMR?
Havnt used anything like it before so taking the best advice i can
ImTriggerHappy
Supporters
- Feb 25, 2015
- 5,374
- 2,228
When you buy get the advanced then you will get the better firmware and all the stuff to connect it to your phone for easy programming.
Installing is easy if you have some level of technical ability otherwise best left to a tech.
Set up just run the pre-cock at medium or high. Set the equalizer to your preferred lenth of trigger pull. And obviously set it to safe semi semi.
Only other thing is if your site has an issue with dmr's that can fire too fast it does have delay settings that can be activated if needed.
Installing is easy if you have some level of technical ability otherwise best left to a tech.
Set up just run the pre-cock at medium or high. Set the equalizer to your preferred lenth of trigger pull. And obviously set it to safe semi semi.
Only other thing is if your site has an issue with dmr's that can fire too fast it does have delay settings that can be activated if needed.
Last edited by a moderator:
- Thread starter
- #5
i know the site im going to said a DMR is any only semi gun but if i use the titan to have a 3 second trigger delay theyll class it as a sniper and allow it to be up to 500FPS
Thanks though. Ive upgraded parts of my gearbox a few times though so this shouldnt be too hard hopefully
ImTriggerHappy
Supporters
- Feb 25, 2015
- 5,374
- 2,228
It is pretty easy to fit just look at the online video and treat the boards gently.
Don't use too much grease in your gearbox either as it screws up the light sensors.
Don't use too much grease in your gearbox either as it screws up the light sensors.
I have one, very positive upgrade. Total control.
My only negative is the cables are very stiff (no biggy) and be careful bending the motor contacts as they snap easily.
Nothing more to say that hasn't been said already. ? Well worth it.
ImTriggerHappy
Supporters
- Feb 25, 2015
- 5,374
- 2,228
Yeah they do use a horrible wire but I always replace it.
As for the motor contacts no matter which ones you use they are always weak. The trick is to bend them then put a dab of solder on the inside of the bend. Just make sure the open end is facing up so the solder doesn't flow in and fill it.
- Thread starter
- #9
Are the wires good enough to hold up against a High toque Motor and Gears with a 140 Spring(if I remember correctly) They aren’t going to get hot or anything?
Edit : It’s a 140 Spring with a SHS High Torque Motor and big dragon 100:200 Gears
Last edited by a moderator:
ImTriggerHappy
Supporters
- Feb 25, 2015
- 5,374
- 2,228
They will be fine.
A high torque set up shouldn't create too much heat and no AEG should get close to wire melting hot.
The quality is ok they just use a stiff coating.
Last edited by a moderator:
I swapped mine out for the type that are like a washer (rather than push ons) so I could screw them onto the motor. I don't know if only certain motors allow this as I've only installed a titan once and the stock motor had this type of connector by default. I snapped the original titan ones :lol: Doh!
Good tip on the solder ?
- Thread starter
- #12
Mine did but i think it was the fuse, the Battery, fuse and motor got hot, thankfully ive ordered a new motor and the titan so any problems with the wiring or maybe motor should be fixed
Adolf Hamster
Supporters
- Feb 1, 2018
- 7,057
- 2,229
mintsauce5
Members
- Jan 22, 2015
- 164
- 14
I’ve got two titans now , really nice bit of kit just found the motor wires a bit on the short side
- Thread starter
- #15
mintsauce5
Members
- Jan 22, 2015
- 164
- 14
Mine were plenty long enough, perhaps even too long for one post so it was tucked round to make it short enough to hide in the handle.
May depend on what your installing it into and I guess you could always replace wire as ImTriggerHappy said if it was an issue.
(Mine is rear wired too btw)
May depend on what your installing it into and I guess you could always replace wire as ImTriggerHappy said if it was an issue.
(Mine is rear wired too btw)
Last edited by a moderator:
- Thread starter
- #18
Ive fitted it to my build, it is so cool, Being able to see how your gun performs and its average stats are great
Love tweaking the select fire and how many bursts it can do
@mintsauce5 i did have your problem of short wires tho on the Red Motor connector, it was annoying to connect to the motor but it fit
Love tweaking the select fire and how many bursts it can do
@mintsauce5 i did have your problem of short wires tho on the Red Motor connector, it was annoying to connect to the motor but it fit
Swampysteve
Members
- Dec 28, 2018
- 76
- 13
I've gotta gets me one of these!!!
Lozart
Supporters
- Jun 24, 2013
- 8,493
- 4,941
Finally got around to fitting my Titan to my Specna M4 last week and ran it at the weekend. Absolute beast, totally love it. I've also fitted a Maxx CNC trigger as they have been designed to work with the Titan (and it looks nice). Fantastic response, well needed battery level warning and protection cut off. Bought the Advanced set with the USB link so now I can tweak my gun on the fly as long as I have the cable and my phone!
Similar threads
