G&G MOSFET

E21A said:
LOLs, I’m using a 30c as advised 
Click to expand...
Click to shrink...


30c ??? getting a bit quick to me

15~20c is a bit lame, 20c min, 25c is what I tend use

but specs or stickers vary, the zest factor is a bit of myth or open for debate tbh

NORMALLY 25c about 2000mah is a decent-ish battery

others say a bigger battery say 3000mah provides a lot more punch than a 1200mah same 25c

well - maybe but I got a 1300mah 33c 11.1v and that f*cker has shredded more pistons taking the pi$$

than any other battery - think its output is way more than the label and the cells are well out of balance

Any battery you get for your mobile from China say is often half the rating written on the outside

so tbh take "some" of these specs written on outside as only a ROUGH guide to its real performance

(I trust little of manufactures claims but most decent makes hold kinda true to their spec)

The main issue with ramping up the juice is the stock motor inside

G&G use 3 main types

Grey 18k std lame motor in my old FFR A2

Blue powerful 24k motor in some others CM18, FireHawk, some older TopTech's etc...

Orange Ifrit 25k neodym motor

Depending on motor inside will dictate just how fast the guns cycles and the risks

If using a 11.1v 30c LiPo with the Orange Ifrit then you are likely to hitting say 24~26rps I'd guess

at around 24rps many guns will overspin a fair bit and risk double firing

Though ETU might help kill the cycle a smidge sooner, the cycling is a bit quick for a UK stock spec gun

Remember Krytac had to install a 20k motor but some grey/gray imports had the 30k motor

with a M95/100 spring on a 30k motor - throw in a 11.1v some guns wrecked themselves coz was too quick

fine if you have a US 390/400fps gun on m120 on 11.1v

But a 340fps going nutz PME could take place and stuff starts to break

So we normally go with a reasonable 18~23rps as a nice safe rof for UK guns

unless you do the work of Short Stroking or running a slightly slower torque motor to ease up on rof

normally nudging twenties is plenty

going higher than mid twenties on a stock gun is pushing it or increasing risk of PME

redo the box and yeah mid 30's is achievable

but if G&G are still using their stock black plastic single tooth piston - I'd be inclined to go easy on da juice/burst

 
Piston is also covered under sharps warranty for 6 months too 

Thinkjng I may drop down to 25c as there seems to be more choice, only 30c I can find that’ll fit is a Nuprol 

 
More to the point, how would they know?? 

 
Hey I have two etu2.0 which typically come with the 3.0 MOSFET and I can say right now I've had absolutely no issues what so ever and I believe they are the absolute most cost effective way to dramatically improve your guns trigger response while keeping costs low my main gun has one and alongside my other upgrades it will keep up with any hpa system ive come across all my buddies are hpa freaks and they are all speechless when using my AEG

 
Hey I have two etu2.0 which typically come with the 3.0 MOSFET and I can say right now I've had absolutely no issues what so ever and I believe they are the absolute most cost effective way to dramatically improve your guns trigger response while keeping costs low my main gun has one and alongside my other upgrades it will keep up with any hpa system ive come across all my buddies are hpa freaks and they are all speechless when using my AEG

 
Also I'd like to add as I see miss information here the ETU is not a MOSFET but they come as a package deal often you can buy an ETU2.0 which will more than likely come with their MOSFET3.0 the MOSFET does have precocking it does have active braking and does have low LiPo cutoff i experience all three everytime I use my gun it does also have 3 round burst function I know vid is shit but you see the BB's and hear the gun also keep in mind that I'm running an 11.1v LiPo with 20c discharge and rps is mostly due to shs 45k motor and shs 13:1 gears but never the less trigger response is by far best bang for your buck 

EDIT: not sure why can't see the vid but you can hear it so that's all you really need

View attachment 44998

 
Last edited by a moderator:
You must log in or register to reply here.
Back
Top