• Hi Guest. Welcome to the new forums. All of your posts and personal messages have been migrated. Attachments (i.e. images) and The (Old) Classifieds have been wiped.

    The old forums will be available for a couple of weeks should you wish to grab old images or classifieds listings content. Go Here

    If you have any issues please post about them in the Forum Feedback thread: Go Here

Search results

  1. S

    G&G GEC36 The lonely owner's thread

    If it is doing the odd power-drop shot it might be cycling too fast and the nozzle isn't seated in the bucking when the air is pushed through. Maybe a stronger tappet plate spring (either new spring or cut a coil off and re-loop the end for more tension) My mate has the G&G G36 and it has...
  2. S

    TM M733 snappy semi build questions

    Ran the M733 today at UCAP VENDETTA and it worked really well. Not quite the range of the MWS and I had one semi-lockup (at the worst possible time…so I switched to my USP and forgot the safety was on ?‍♂️) Trigger response and cycle time were plenty fast enough so no 11.1v or pre-cocking on...
  3. S

    IWA 2023 - New releases

    +1 for getting a Cyma Platinum, ZCI hop / ML rubber and throw in a Warhead motor - all for less than this stock!
  4. S

    Gun picture thread

    TM M733, Vortex red dot, TacBelts minimalist sling, Scout light clone on genuine Magpul mount (butchered by me) and an E&C non-clone correct grip (fight me!) Internally it has 16:1 gears short stroked 4 teeth (2 pickup / 2 release) shimmed and Warhead HS motor. XT M110 spring is giving...
  5. S

    XG02 Propane adapter

    It looks like the thread will be the smaller one for Butane-mix camping stoves, not the larger Propane ones. Will pop out to the shed later and check as I have both types and a Madbull knock-off fill valve :) EDIT - yeah they are different- see pic
  6. S

    THE TM MWS thread

    No but the Hao bolt end and AG steel buffer gives a nice kick! I have an AG Alu buffer and a DP lightweight bolt if I need to reduce the gas consumption / run it in single digit weather.
  7. S

    DP Nozzle valve

    Is it just the little aluminium valve part that goes in the nozzle? If just that there won't be much (if any difference) but it might be a little more consistent than the stock TM one. If you include the spring that comes with it is a) longer and b) stronger so you will get a jump in FPS -...
  8. S

    Upgrading a cyma 48

    This is most outdoor games :) I asked ChatGTP: Q: What is the best upgrade for my Airsoft replica? A: The best upgrade for your Airsoft replica depends on your specific needs and preferences, as well as the current state of your replica. However, here are some popular upgrade options that...
  9. S

    Load-Out / Loadout Picture topic

    Pistol belt set up, just the bits I need for CQB or in support of the M4 / SADF M83. Shout out to the KydexCustoms adapter to fit the holster to the mid ride plate and Tactical-kit for the extra pistol Kywi (and free stickers I forgot to add to the cart!) USP in Amomax holster, KydexCustoms...
  10. S

    TM M733 snappy semi build questions

    So finished* the M733. Warhead high speed motor, G&G 16:1 gears short stroked 2 pickup/2 release, metal bushings and shimed. Lightweight piston with 14tooth metal rack and new POM head, 3/4 cylinder. XT M110 spring and radiused the gearbox shell. E&C pistol grip as the TM one was...
  11. S

    BBs in bulk

    Just tested all the BBs I own in my new (to me) TM M733. 300mm polished brass barrel, Macaron 50deg rubber, shooting 320fps on 0.20g. RIF was clamped, and some warm up shots fired and hop set. 10 shots fired at 10m and the diagonal of the box around the hits measured. *Warhead 0.28g - 43mm...
  12. S

    Short stroking 4 teeth on 200mm barrel

    Some good advice here, I am looking at losing 3 (maybe 4?) from my build and was going with 2 from release, 1 from pickup but after reading @Adolf Hamster great explanation I think I will lose two pick up, one release to avoid timing issues with the tappet plate. This contradicts what Luke at...
  13. S

    Odd double clunk in TM AEG

    Update - the gearbox was well shimmed and all running well. Spring wasn’t chopped and firmly fitted in the piston (no shifting it!) and not rattling on the guide. I am swapping out the 6mm PLASTIC bushings for some steel ones and shimming as A) they won’t last long with an M100 spring and...
  14. S

    What have you made?

    Can’t be bothered to try and make a barrel clamp on RIS fit under the front sight so I trimmed a Polymer Magpul Mlok extended rail to suit ? Clamps through the holes in the fore end and keep the light out the way. If my repro light had threaded holes I could lose the clamp and bolt it directly...
  15. S

    New AK firing hot

    Play a couple of games and see how it goes. As others have said the hop rubber and barrel can make a difference- although cleaning the barrel with the unjamming rod and alcohol soaked rag is a good shout as there is usually gunk in it from the factory ?
  16. S

    Odd double clunk in TM AEG

    Just got the TM M733 and on testing noticed that there is a double clunk - first is the piston head hitting the end of the cylinder but then there is another - possibly the piston bouncing? Loose spring guide? Chopped spring. FPS is +/- 3fps and shooting 295fps on 0.20g BB so it is working...
  17. S

    Short stroke 4 teeth on 200mm barrel

    I would say that is a pretty damn fast set up! Are you running it on 7.4 or 11.1v? I am not sure changing the nozzle length will sort the feeding issues - more likely to drop the power due to bad seal on the rubber. If it is not feeding I would look at trying a delayer chip (if one isn’t...
  18. S

    Oooh so tempting! G19 is a little small for my hands 

    Oooh so tempting! G19 is a little small for my hands 
    • SSPKali
    • Profile post comment
  19. S

    Nuprol green gas 2.0 vs 3.0

    When I tested it in my MWS the FPS went from 260fps to 275fps on average. Good for colder weather when gas guns can get a bit sluggish. No idea on the PSI but pretty sure I have seen a chart on the Internet somewhere - have a Google!
  20. S

    Your best/worst RiF?

    Worst - Tie between G&P MOTS M4 with recoil (was a PITA to work on, really picky on mags and ammo, always "meh") or the TM MP7 as while when it works it is great there are so many design flaws and pretty much zero after market support. And it is scaled down. It could be so good but....TM...
Back
Top