Search results for query: *

  1. Enid_Puceflange

    The 'What have you just bought' Thread

    The Pulse is a variable timed grenade. There’s a blue adjustable “valve” on the top of it, you pop it upwards, adjust the timing delay by turning it, then push it back down to secure. I’ve had one a while and found it very good. Set up time from shot to shot is very much the same as using a...
  2. Enid_Puceflange

    Possible paint removal advice.

    I’ve always used petrol I found acetone did do the job eventually, but it was tediously slow! Petrol won’t damage the plastics or the metal, and it won’t damage the original paint on the metal parts of the mags Obviously, it’s a job for outdoors. But it works incredibly well 👍
  3. Enid_Puceflange

    (MP7) To Supress or not to Supress

    How did you get on?
  4. Enid_Puceflange

    (MP7) To Supress or not to Supress

    Yeah, it’s a cheeky wee scamp 😁
  5. Enid_Puceflange

    (MP7) To Supress or not to Supress

    Yup Just up to where the flash hider ends Don’t go dunking the whole PewPew!🤣
  6. Enid_Puceflange

    (MP7) To Supress or not to Supress

  7. Enid_Puceflange

    (MP7) To Supress or not to Supress

    I’ve had success with heat. One method I’ve used is to dip the flash hider into a bowl of water that’s just off the boil from your kettle. It’ll warm it enough to soften any glue if there is some Another is proper direct heat, so a chefs torch, or over the gas flame on your hob is another...
  8. Enid_Puceflange

    T238 mini loader

    I just have to give some feedback regarding Alice @ Amethyst/Sabre airsoft I let her know the switch levers she sent me were outta shape when they arrived, but were recoverable… She offered to send out replacements which is awesome. As I so was impressed with the quality of the switch levers...
  9. DTSS .308 Suppressor 14mm Thread - New

    Question by 'Enid_Puceflange' in classified ad 'DTSS .308 Suppressor 14mm Thread - New'

    Nice box! Anything in it? 🤷🏻‍♂️
  10. WTD Missing Parts

    Wanted Rifle WTD Missing Parts

    I recently picked up a built & “upgraded” sniper Popped a few mags through it and it’s very inconsistent Gave it a strip and relube and got better fps, but discovered parts missing from the hop unit. Does anyone have the small spring and the rubber ring aeg adapter for an AirsoftPro hop unit...
  11. Enid_Puceflange

    The 'What have you just bought' Thread

    Yeah, I’ve had a few mags through it, and pulling the shroud down, gives easy access to feedlips to use a normal speed loader Cheers
  12. Enid_Puceflange

    The 'What have you just bought' Thread

    I did look at the mags and wondered what the best way to load them was, what do you use?
  13. Enid_Puceflange

    The 'What have you just bought' Thread

    So a 130 mile round trip saw me bringing this home last night Cyma Cm.702 , heavily upgraded with AirsoftPro bits n bobs Bought as it sits with scope & bipod (Scope is a silly 3.5-10 x 50 waaay overkill for Airsoft) Previous owner has finished it nicely in an FDE colour, which suits my tastes, I...
  14. Enid_Puceflange

    The 'What have you just bought' Thread

    Picking up my first Sniper rifle in almost ten years of playing Disgusting sneaky little buggers they are, but if you can’t beat em - join em It was too good a deal to walk past, I’ll pop picks up after the 4hr round trip is completed 😂 (Mind, I say 4hrs, it’ll take longer as we are going in my...
  15. Enid_Puceflange

    TRMR multi shot and Timed BFG (additional calibers)

    Dynatec’s seem to go for around £50, though yours is a bit more desirable with the 12g adapter Trmr’s circa £80-£90 I’ve had no problems posting grenades, blanks would be questionable though I have received them in bundles before 👍
  16. Enid_Puceflange

    Where to source TM HK417 parts?

    Contact Sam at Kindom of Airsoft Fb messenger is best , he’s always busy but normally replies within 24hrs
  17. Enid_Puceflange

    T238 mini loader

    I received my Amythst/Sabre parts earlier today. Slightly too tight a tolerance for the bbs to feed through, so that’ll need a rub with fine wet & dry just to remove a fraction of material to allow the bb’s to pass through easier (needs excessive force as it sits) Also they are oval in shape...
  18. Enid_Puceflange

    New Load Out

    I like my replicas to look realistic, but I can see these in the RS world being Range Guns, I’d definitely put these on the “Cool Wall” 👌
  19. Enid_Puceflange

    Gun picture thread

    I tried that out a good while ago It was just waaaaay to heavy 😬
  20. Enid_Puceflange

    T238 mini loader

    From what I’ve been told, if you print that part (the switch lever) in pla , it’ll probably not last long. But to answer your Q….. a picture paints a thousand words, an all that. Here’s Stupid Airsofts video fitting it, a two second job View: https://youtu.be/clAg5oPy3F4?is=AAnXwtNActOEIfUb
Back
Top