Search results for query: *

That's really good to hear @andrey. Might be worth having this post as a sticky thread as it's so common in the Ares EFCS. When mine failed, I only used 7.4V 2600mAh LiPo. The first replacement mosfet I got from Ares was the updated longer type that you have there @andrey and the back of the...

Hi, have you made any progress with this? Chris 

Are you talking about the G36 variant or just Maxx hop units in general? All of the Maxx G36 hop units I've purchased up until recently have been amazing, can't fault them, but it's more of a simplistic design that of the M4 variants. @Aj698: if you have the two part hop nub tensioner under...

Ares sent me some replacement EFCS boards but there are two flavours of board design.... My original is the bigger 'L' shaped PCB while the one Ares sent is a more updated version that's rectangular shape but overall it was longer... I had problems fitting the back plate with the dust cover...

Hi Aj, I have the Maxx Begadi G36 hop units fitted in several of my G36's and I can say that hands down its the best hop unit for this. As long as you stick with the standard nozzle length, it'll work fine with the maple leaf and Begadi buckings (I can confirm this). No UK supplier as it's a...

Hi Andrey, Yes I did get that the bottom of it, after a bit of bench testing and probing, I found that a 3.3V SMD regulator wasn't getting power directly from the battery, this 3.3V SMD regulator powers the hall sensors for the selector and magnet in the sector gear, and following this back, I...

UPDATE: So this is the response from Ares technical help... See what you think; 'Our technician said our gearbox cannot support the brushless motor because of the gear ratio. Also, the brushless motor doesn't have enough torque to hold the spring causing the voltage rise. Please try to use...

There is a silicone insulating film in the shape of the PCB board, hard to see but it's there, (can see it covering the middle bearing) Upon further testing, the top two FET's are dead (nothing on the volt meter when in diode test mode). I have another working G36 E.F.C.S. mosfet that I'm...

Good day airsofters, Has anyone installed any brushless warhead motors in combination with Ares EFCS (electronic fire control system) or any other mosfets and have you had any issues after a while? Namely EFCS's burning out... Seems I'm the only person in the world that's had back luck with...

I have to add that I have another Ares G36E that has the same EFCS MOSFET and a warhead motor installed on it too which is still working fine.  I can't see how a brushless motor that draws less current than a brushed can fry power transistors... These are rated for 30V D.C. at  109Amps. Chris

Hello UKAF members. I'm currently having issues with an Ares G36C that keeps blowing it's EFCS (Electronic Firing Control System) mosfet board. It's on its 3rd one now and the problem seems persistent. Upon testing the components on the EFCS circuit board, the FET's (Field effect transistors)...

Hello there! I need a few tappet plates 3D printed for a Vz.61 scorpion so was advised by another forum member to put a request out if anyone can help me? I'll probably need a few 3D printed, so if anyone is able to do this for me please PM me with a cost to do it all. File is here: ...

Reaching out to you guys for some much needed help... I broke the tappet plate on my ASG Vz.61 Scorpion and I'm finding it impossible to source a new one. I believe it's a generic part shared in most CMG/ AEP's so it's the same at the MP7 as well. Been searching for a TM one as the ASG looks...

No it's an Ares one. Thank you for the link though, I'll try them. You'd have thought a 40mm killflash would fit a 40mm scope wouldn't you. Those Chinese eBay sellers are useless!

What 'M' rating spring have you got in there at the moment?

Hi,  I've recently got a clone Elcan spectre for my L85 and the front of the scope has screw threads for various flip up protectors/ mesh kill flashes and wanted to get a mesh protector... I've measured the inside of the scope threads to be 40mm so ordered one off eBay that was advertised to...

You take the RIS rail completely off with the 2 rear screws and front one. This leaves a dove tail mount on the gun. You have to slide it off/ on from the front I believe 

Thanks for your comment @Steveocee. Although it appears to be a bit of a frankenbuild, the gun frame is all Ares, and as I say earlier, the gearbox is also Ares, along with the upgraded cylinder head and nozzle. Now I personally don't like Ares guns out of the box as they don't perform well...

Hi guys, need some help valuing my Ares L85 carbine AEG. Bought the bare frame recently for £90 (no scratches or wear to body) almost like new. Bought a brand new gearbox, stainless steel Ares cylinder head and nozzle from Asia Airsoft for about £100 incl. Postage. Checked shimming, change...

email wargamegearhk, just ordered some missing parts off my Ares Tavor recently; rear sight and rear butt pad pin. They're proper Ares spare parts but you do have to wait a week or so for them. [email protected] Email them your Ares model number and they'll send you an exposure plan...