• Hi Guest. Welcome to the new forums. All of your posts and personal messages have been migrated. Attachments (i.e. images) and The (Old) Classifieds have been wiped.

    The old forums will be available for a couple of weeks should you wish to grab old images or classifieds listings content. Go Here

    If you have any issues please post about them in the Forum Feedback thread: Go Here

Search results

  1. n1ckh

    Magazine Valves

    Just wondering if theres any valves similar to say inner tube valves for hpa where it's a one way valve with a ball bearing or something ??? Bored nay tired of losing air from the magazine everytime I disconnect for a mag change.  If nothing like it exists, has anyone tried making something...
  2. n1ckh

    Lonex Motor

    Double post
  3. n1ckh

    Lonex Motor

    I've put a Lonex A2 motor into my ICS sportline M4 & its screeching. The motor height is ok & I know its down to the pinion gear. Thinking of putting the pinion gear from the standard (removed the pinion gear from the slow motor) motor onto the lonex motor.  Will I get the screech...
  4. n1ckh

    Leaky regulator

    Sup guys. Was going to chrono my rifle today (much needed time off work) as put in a new barrel & noticed air leaking from the reg  What lube do people use ?? as thinking of soaking the o rings in silicone oil like most of us do on our gas mags  Nick 
  5. n1ckh

    Gas mags

    Hi collective minds.  At the moment. After a day of use, I take my hpa valves out & put the normal valves back in the mags then add a bit a gas to keep the seals lubricated.  It's becoming a PITA doing this just for storage.  Do you guys do anything differently or is there other ways I...
  6. n1ckh

    NPAS issues

    Got an NPAS fitted in my masada now & the installation went easy.  Problem I have now is.....The NPAS is wound in so to give maximum FPS on my Acetech 6000 chrono, the fps seems to jump around quite wildly.  I've adjusted in & out but still the same issue  Any suggestions??? TIA
  7. n1ckh

    Bit of a problem

    So...my first outing with my newly tapped masada today (thanks to the guys who've helped me)  Got to chrono & it's pants. On .25 it was to hot. Lowest I could go was 40psi on the regulator & wouldn't cycle after 1st shot, increase PSI & increased the FPS.  48ci proto bottle, 8mm...
  8. n1ckh

    Regulator usage

    What do you do with your regulator after a game day & storage ??  Do you leave it on the tank & switched on or remove it from the tank completely ??  Cheers guys 
  9. n1ckh

    HPA noob

    Hey guys Been a while since posting. I'm venturing into HPA by converting my gas mags to HPA for my WE masada. Ordered a line, tank & reg but already have the mag valves.  I want to run a 13ci tank on my plate carrier & have a 48ci tank ordered.  My questions are.....what do I need to...
  10. n1ckh

    Molle waist pack

    Recently bought one for a milsim weekender next month to put bfg's, smokes (pyro & smoking) bfg blanks, flash bangs & snacks into As I'm using remote detonators, I'll need to carry more bangs, smokes & electronic igniters & that's why I bought it Wondering if theres other...
  11. n1ckh

    Motor maintenence

    My motors are getting a bit sluggish so I think it's time to clean them & replace worn brushes Does anyone else do this & what do you use to clean them with ??
  12. n1ckh

    Magazine compatability

    I've got a tan magpul pmag that feeds in my ICS M4 but not my G&G L85 (doesn't seat in the magwell all the way) I want to upgrade my old mags & like the look of them........but I need them to work in both rifles as I don't need seperate mags then & where do I start looking ...
  13. n1ckh

    Finally done it :)

    So putting a mosfet into a V2 or V3 gearbox is easy (done 3 of my rifles so far) but after a few months of pissing around & putting it off. Got bored today so finally got the wiring done to accept a mosfet into my G&G SA80 Man is it a weird gearbox, took plenty of reference photos as I...
  14. n1ckh

    KJ works G23

    Been having a problem with my Glock for a little while now :( the problem is that the slide will not fully fly forward & gets stuck around the hammer area It's well maintained (cleaned & oiled after every game day as is my M1911) & I put a 6mm spacer ring on the recoil spring...
  15. n1ckh

    Possible gearing change ??

    Hi guys. I'll start of with what I have which is ICS M4 with stock motor, M100 spring, mosfet & 7.4v Lipo JG G36C with high speed motor, M100 spring, mosfet & 7.4v Lipo Each sector gear has a delay chip but other than upgraded piston (plus head) & cylinder head then there pretty...
  16. n1ckh

    Looks like kyle sessions has done it

    Well, who can remember Kyle sessions & his posting of his Nazi uniform ?? Well looks like he's gone & done it, he's worn it to a game day at black ops airsoft portishead site Annnnnd they've posted a photo of him in it, as I can't link it, check black ops cribbs Facebook page to see it
  17. n1ckh

    Radio waterproofing

    Now the weather's really closing in, what do skirmish day & milsimers do to water proof there radios ?? I'm thinking a sealable plastic bag with holes for antenna & pin connectors into the radio then tape around the holes
  18. n1ckh

    In game photos

    Does anyone use a small digital camera you can carry in your pocket for in game shots when there stood around waiting for a medic or when your laid up waiting etc ??
  19. n1ckh

    2 pin kenwood PTT

    I'm wondering if there's a PTT module avaliable that works with a programmable radio that if you push a switch one way, it allows you talk on 1 channel/frequency then if you push the switch the other way it allows you talk on another channel/frequency ?? I've seen PTT's that will work with 2...
  20. n1ckh

    G&G L85a2 mosfet

    I understand the l85a2 from G&G has a piece of wire connected to reduce/stop over spin Has anyone wired in a mosfet ?? Did you use non brake or active brake fets ?? Cheers guys
Back
Top