• Hi Guest. Welcome to the new forums. All of your posts and personal messages have been migrated. Attachments (i.e. images) and The (Old) Classifieds have been wiped.

    The old forums will be available for a couple of weeks should you wish to grab old images or classifieds listings content. Go Here

    If you have any issues please post about them in the Forum Feedback thread: Go Here

Search results

  1. n1ckh

    Gas VS Electronic

    Even with gas your snookered if there's a power cut & the spark ignitor doesn't work as not many non smokers will have matches or a lighter in the property (which they should for this very reason) I have windproof matches, a lighter & fire steel in a tin in my combat jacket
  2. n1ckh

    What have you just 3d printed (for airsoft)

    A mate of mine spent a number of hours using a computer program to design a spacer for his E&L AK as he says the magwell on these can be a problem He says he's made/making a PDF for other people with the same rifles so they can get one 3d printed. I think it's costing him about £6 in total...
  3. n1ckh

    Taking "illegal" grenades

    Glad to hear I'm not the only one to do it :) last time I did it, the guy said he stood there staring at it thinking it should be fizzing & then someone popped him & another guy :) he did say he'll try it I do it when I've run out of pyros aswell
  4. n1ckh

    Taking "illegal" grenades

    Something I do which does work at getting people running is throw a used paper pyro & shout grenade, it throws people off guard & then they get shot by someone/anyone Its just to clarify that I do it to throw people of guard & to scatter. Its for no other reason & people always...
  5. n1ckh

    What have you just 3d printed (for airsoft)

    I use plastidip for waterproofing my electronic throttle unit in my rc cars & boats plus the servos for steering etc In airsoft, about the only thing you could use it for is the soldered contacts on the trigger units & solder joints of battery connectors before heatshrink is applied but...
  6. n1ckh

    Taking "illegal" grenades

    Imo if it don't go bang then it's not a hit All sites I've played at so far so say paper pyros can be thrown over arm (if they hit you then it won't hurt) reusable grenades are thrown under arm long as it's not towards someone's head So simple fact for me is player B is a cheat for not taking...
  7. n1ckh

    Both eyes open optics.

    Pretty much where I position mine If it's right up against your eye, you get a blind spot like you do with car mirrors cause the sight/red dot is in the way
  8. n1ckh

    low voltage

    If he's got a programmable charger then put on balance charge (set the MAH cut off to the MAH rating on the battery) & charge at 0.1 amps (basicly trickle charge) until the display reads 3.60v in each cell & then change to normal charge rate If it's way below 3v then its fooked completely
  9. n1ckh

    Both eyes open optics.

    I use an eotech 552 on my M4 & my acog on my SA80. The point of a red dot is so you can keep both eyes open & also for quick acquisition. I keep both eyes open & both red dots are away from my eyes, I can keep the dot on target while being able to look around The susat on an SA80 is...
  10. n1ckh

    G&G cm16 srl battery issues

    When I installed my mosfet, after a while I would get intermittent firing. Took the gearbox apart & found the signal wire I soldered on had come off so cleaned it a bit more & resoldered & been fine since
  11. n1ckh

    Help fixing ICS L85A2

    End of last month, I lent my L85 to a player because his ICS l85 was having similar problems, a little lever would jump where the trigger unit is located that would give him intermittent trigger response, a few of us looked at it & suggested something had to be done to that little lever...
  12. n1ckh

    TM Glock 18C birthday pressie :)

    I'd check with American & British customs/airports on how to transport them back as there pressurised containers which for obvious reasons are not to welcome on-board flights
  13. n1ckh

    Milsim Calendar

    That's simple enough to understand Baz :)
  14. n1ckh

    RIS to Outer Barrel/ Receiver Compatability?

    I bought both my free float rails from ak2m4. So easy to install :) take of old rails & barrel nut, screw on new barrel nut, screw on rail & tighten screws Job done
  15. n1ckh

    Helmet/goggles/mask

    I know there's a video on YouTube where a guy has redesigned his head gear to incorporate ear defenders (radio speakers) where he used nuts & bolts plus the rails I was thinking of permanently attaching my face gear to my helmet but sometimes I wear mesh goggles or ballistic sunglasses when...
  16. n1ckh

    Helmet/goggles/mask

    I cable ties my mesh lower to my goggles (inspiration from one of the guys on here) but as I don't always wear a helmet, I haven't attached them You could just run the elastic strap around your helmet & pull the goggles down when in the game area
  17. n1ckh

    Possible gearing change ??

    Far as I know, there's no real difference between high speed & torque gears but again from my understanding, low ratio gears need a torque motor to turn them better when using high rated springs To increase fps - better airseals on nozzle, cylinder head & piston head plus a higher...
  18. n1ckh

    Teeth shot out

    That's ok mate so don't worry but again fairplay for your charge :) Are you going back end of this month ??
  19. n1ckh

    Possible gearing change ??

    Cheers duck, I knew you'd come to the rescue lol But yeah, it's usually the spur gear that's got more or less teeth
  20. n1ckh

    Possible gearing change ??

    Hi guys. I'll start of with what I have which is ICS M4 with stock motor, M100 spring, mosfet & 7.4v Lipo JG G36C with high speed motor, M100 spring, mosfet & 7.4v Lipo Each sector gear has a delay chip but other than upgraded piston (plus head) & cylinder head then there pretty...
Back
Top