• Hi Guest. Welcome to the new forums. All of your posts and personal messages have been migrated. Attachments (i.e. images) and The (Old) Classifieds have been wiped.

    The old forums will be available for a couple of weeks should you wish to grab old images or classifieds listings content. Go Here

    If you have any issues please post about them in the Forum Feedback thread: Go Here

Search results

  1. S

    S&T G36 Titan V3

    I've only got one detent on my WE. I was able to stop reward travel of the selector plate with an extended case screw, but I'm presuming it goes too far forward in your case.
  2. S

    S&T G36 Titan V3

    Make sure both sides of the selector lever are even. If the right side is misaligned it will keep the safety on. Only the last bit of travel removes safety. That spring looks meaty too. Also I suggest putting a ball bearing in the lh selector instead of plastic it you have a plastic detent in...
  3. S

    WE 999 DMR

    Hello, I fancied a DMR so I thought I would convert my G36k I think it is. There's nothing special going in, just a stronger spring and a simple MOSFET for the trigger. Here's the gearbox, I'll add more as I get on with it. I was able to lock it to semi by using a longer gearbox bolt and...
  4. S

    Tokyo Marui MP5 NGRS SMD identification

    Me too, not a zener. I've looked at the lists again, there's some voltage regs in 5 pin. More than one sadly. https://smd.yooneed.one/code5931.html That's your y1s and whilst they are mostly zeners, there's a few regulator, detecting, etc ics in 5 pin. I've looked at a few of them and we...
  5. S

    Tokyo Marui MP5 NGRS SMD identification

    It's a zener diode mate. 25 to 2.5v Likely 9v or 16v depending on what it's doing.
  6. S

    AK2M4 / XT Brushless Motors

    Uh magnets seem overkill for a 150w motor, but the specs look all but the same. https://m.airsoftmotor.com/airsoft-motor/long-shaft-aeg-motor/high-speed-39k-cnc-brushless-airsoft-motor.html
  7. S

    AK2M4 / XT Brushless Motors

    My understanding of precocking is that it's just a delay in removing power after the trigger is released. This won't affect the motor or MOSFET. AB is more problematic, if it's shorting the motor it's possible to damage the motor electronics and no reason to suspect AB even works on a brushless.
  8. S

    G36 hop unit

    It looks like it's a guide for the nozzle to centre it as it gets close to the hop rubber. The nozzle in these goes quite deep into the hop and may be pushed up by the bbs on the underside and the plastic bit at the top pushes it down towards the centre of the opening which is quite snug. Maybe...
  9. S

    Plastic outer barrel vs steel one

    Its the paint scratching isnt it? I guess you can leave the plastic barrel in place but the wear on it may be more, soft plastic vs hard metal sort of thing. Functionally it shouldn't make any difference. I thought a tilting outer barrel was necessary to allow the slide to reciprocate even if...
  10. S

    The gutless wonder...

    Again back in the day we added spacers to precompress the springs...
  11. S

    CO2 Blowback reduction

    In my co2 mags for a we big bird there is a fine mesh which serves to reduce pressure. You may be able to fill the mesh to reduce the area that lets gas through. However it's the rocket or flute valve in the bbu that determines how much gas goes down the barrel. Reducing the spring tension or...
  12. S

    TM MP5 NGRS Owners

    I can measure my mag release (cyma mp5) if you want, you measure yours and compare? The TM one has two grub screws the others have one. The TM one is an anodized machined aluminium part ( maybe cast or from a lump) and the others, mim.
  13. S

    Cyma mp5 041sd6 parts

    I don't know how handy you are but if you epoxy the two parts together, drill it out and sleeve it with brass tube. Or print one https://cults3d.com/en/3d-model/gadget/cm041-sd-silencer-mounting
  14. S

    Cyma mp5 041sd6 parts

    https://www.patrolbase.co.uk/cyma-cm-041-sd-aeg-silencer-mounting-apparatus It's out of stock here.
  15. S

    Motor advice

    Ignore 
  16. S

    AK2M4 / XT Brushless Motors

    Currents, 7.4 and 11.1 22tpa xt 17 and 25 BL xt.      15.5 and 20.5. Ah I forgot to take precocking off...wondered why auto was so similar to semi if not a little more. The BL is much faster, esp at 7.4v in comparison, but I haven't sorted my feeding issue. BL motor isn't fitted properly I...
  17. S

    AK2M4 / XT Brushless Motors

    You need some sort of electronic commutation and sensors plus a lil computer to work out when to commutate. The main difficulty in making the BL motor like a brushed motor is that the BL needs power to work, MOSFETs have a polarity and the board needs electrical protection that Brushed ones...
  18. S

    AK2M4 / XT Brushless Motors

    The motor has to follow the same form factor as existing motors and a single case for long and short motors makes sense, at least for the smaller producers. I don't think there's a case for a reversable motor, unless you can think of a reason why you'd want such a thing. Brushless motors can't...
  19. S

    AK2M4 / XT Brushless Motors

    As a motor, the brushless is 1mm shorter, compared to the xt brushed, from the motor front to the pinion end, the motor tower has no play in it. Altho I would suggest this dimension could be adjusted as the shaft was probably a bit longer originally. The motor appears to have strong magnets...
  20. S

    AK2M4 / XT Brushless Motors

    I fitted mine to test and it functions just as the brushed motor does. I have a perun. Motor height was different and it needed to be screwed in further. It fit without issue I think perhaps I'll look at bevel height as I've got motor tower play which I removed on the brushed motor. Or shim...
View older results
Back
Top