• Hi Guest. Welcome to the new forums. All of your posts and personal messages have been migrated. Attachments (i.e. images) and The (Old) Classifieds have been wiped.

    The old forums will be available for a couple of weeks should you wish to grab old images or classifieds listings content. Go Here

    If you have any issues please post about them in the Forum Feedback thread: Go Here

Search results

  1. Hudson

    Air nozzle issues

    At a guess, Do you think replacing the hop unit for a marui version might improve this? I'm wondering if the JG unit is ever so slightly off spec in comparison, so it works with their own barrels, but not any others.
  2. Hudson

    Air nozzle issues

    Well after the last, unsuccessful attempt I decided to change tack and go back to the beginning. I changed the barrel back to the stock one, and adjusted the nozzle to match the stock length (despite it appearing to still have the slight gap) and that appears to have sorted it. ? It's putting...
  3. Hudson

    Air nozzle issues

    Update: This is not going very well, like I'd hoped! Still getting the same feeding issues, even going through a variety of nozzle lengths. ?
  4. Hudson

    Air nozzle issues

    Well unfortunately the ultimate nozzles I have are too wide for the hop unit, so I'll have to look for something else. *Edit, called in at BZ Tactical on the way back from shooting, and managed to snag an adjustable nozzle that was supposedly out of stock on the website, so my job just got a...
  5. Hudson

    Air nozzle issues

    I've been looking for some of the adjustable nozzles that I've used in previous guns, but they mostly seem to be out of stock currently!
  6. Hudson

    Air nozzle issues

    I dug through one of my many boxes of bits, and found an Ultimate Sig 550 air nozzle at 22.2mm long. I might try that and see what effect it has.
  7. Hudson

    Air nozzle issues

    The hop unit itself seems ok. Due to the design of the G3 it has an almost fixed position relative to the gearbox, so there's not really any movement back or forwards. I did try using a small spring or o-rings at the front increase the seal, but this just mostly resulted in feeding issues.
  8. Hudson

    Air nozzle issues

    Ok, so I woke up early today and decided to tinker with it again before work. I tested it with the stock bucking & barrel set up and it fed fine, so I went back to the previous one and changed out the bucking. (Was an XT barrel and guarder bucking, now both XT, courtesy of @ak2m4?) and it's...
  9. Hudson

    Air nozzle issues

    See, that's what I've always thought it should be like, before this. Currently, the BB is just getting stuck in the bucking and wouldn't feed. On removing the magazine and turning it upside down it then did fire.
  10. Hudson

    Air nozzle issues

    I'm currently having some feeding issues with a Jing Gong G3, and they're centered around the air nozzle & hop unit. I'm a passable tech, but nothing amazing. I can do the basics but this has got me a little puzzled. The stock nozzle in the G3 is 21.51mm According to what I can find...
  11. Hudson

    M16A1 low fps - theory?

    I'm having similar issues with my JG SG1, so i'll be keeping an eye on this thread. I normally use 0.30s, but adding enough hop causes the power to drop precipitously. It looks to be an issue with compatibility between the hop unit, bucking or air nozzle at a guess so I've got lots of playing...
  12. Hudson

    M16A1 low fps - theory?

    590mm and not 509? A 590 would be longer than the standard M16 length, which tend to be 509mm.
  13. Hudson

    Wtb - Specna Arms SA-E23 EDGE 2.0

    This is the advice section. You want the classifieds section.
  14. Hudson

    Fogging and glasses

    How much, if you don't mind me asking, please?
  15. Hudson

    Fogging and glasses

    I've done something very similar, but with the exfog and for sniping with a full-face veil. https://www.instagram.com/p/C4atDp7t3gB/?igsh=MWhvMThnb2d2OXNkaQ== I've got a couple of different Setups, be it for glasses or goggles, with different mounting styles...
  16. Hudson

    TM p226 Mags

    I don't think that is a TM. TM would say ASGK and Tokyo Marui on it somewhere. I think it might be a Kwa, which would explain the mags! How does the hop up adjust on yours?
  17. Hudson

    TM p226 Mags

    Can you post up some photos of your 226? Both sides, and also ones with the top & bottom separated, and of the hop & barrel unit.
  18. Hudson

    TM p226 Mags

    Are you sure they gave you marui ones? The rear of that magazine looks different to the ones I remember having; there was no detail or markings one them, from what I recall. What store did you go to? Tokyo-Marui-G-31-25rd-Magazine-SIG-SAUER-P226.webp *edit The one in your picture looks...
  19. Hudson

    TM p226 Mags

    When you say they didn't fit, what was wrong with them exactly? I used to have an old 226, and didn't have any issues using the old or E2 mags.
  20. Hudson

    Classic Army CA90 / P90 / CA049P

    When You wind hicaps it's going to require a lot; typically a few dozen winds. (You'll hear the clicking sound change once you've wound it fully). I've been out of the P90 game for a while now; could never really get on with them, so I'm unsure on compatibility but these might be a solution...
Back
Top