-
Hi Guest. Welcome to the new forums. All of your posts and personal messages have been migrated. Attachments (i.e. images) and The (Old) Classifieds have been wiped.
The old forums will be available for a couple of weeks should you wish to grab old images or classifieds listings content. Go Here
If you have any issues please post about them in the Forum Feedback thread: Go Here
Recent content by SeanW
-
S
THE TM MWS thread
Mine went from average of 330 on abbey predator at 20 degrees C to 368 on the same gas at around the same temp. Internals are stock except brass supernub, modify tan rubber and G&p roller for the BCG. Be aware first shot of a fresh mag is high if you leave it to warm up. Also, with... -
S
THE TM MWS thread
Hi Joe I have a V2 buffer as a spare and I just ground about 1mm off each of the sides of the wide end using a diamond file. I then tidied it up using wet and dry with some gun oil. It’s really easy to do. Just make sure not to get metal filings in your MWS. Clean it off before every test... -
S
THE TM MWS thread
@TadsJ2 I am currently using abbey predator/vertex for colder days and have used propane but runs too hot. The valve is recessed quite deep in the mag, is the gas nozzle all the way in when you are filling, the abbey nozzles fit nicely. In order to fully fill a magazine, you should be getting... -
S
THE TM MWS thread
@TadsJ2 I have 6 v2 MWS mags, no mods on the mags, and all fire 2 full mags on a fill (+ nearly a full 3rd mag), using the 1 sec burst technique. My internals are mostly stock, fitted a g&p v2 buffer with all 3 weights and Dave’s HSB. A 370mm, 6.03 barrel and the brass supernub. The o... -
S
THE TM MWS thread
Hi Dave I didn’t expect FPS gain either with the HSB, but the semi action is a great gain. Did you notice I popped the two lubricants in there you recommended too. The nozzle seats really well and the consistency in FPS is astounding. Also managed 2 full mags on semi at 7 Degrees with... -
S
THE TM MWS thread
Hi @MiniLuxy I have the original TM buffer tube and it was still too tight. It does move but not as freely as you would like. The original TM buffer has at least 1mm clearance and in other areas more. It is only the exterior of the end cap that needed some mass removing but it didn’t take... -
S
THE TM MWS thread
Hi @Davegolf The parts are amazing. It just feels better when shooting and cycling. The nub is hands down better than the cut down omega I had as a temporary measure. It does look great in its own skin, not going to lie I am still looking at a 12.5” mk18 rail. Will probably do this if I... -
S
THE TM MWS thread
Hi All Finally had some time to get the G&P V2 buffer fitted. Along with Dave’s high speed buffer insert and brass nub. The v2 buffer must be made for a slightly wider buffer tube and I watched a video on some guy testing the v1 who said he could smell burning. That was metal on metal... -
S
THE TM MWS thread
Thanks @AlphaBear I have read through this entire thread a few times and it is great. I have already received my nozzle spring set. Got a ctr stock. Ordered a brass nub and high speed buffer from @Davegolf Fitted a Prometheus 6.03 barrel, modify tan hop rubber and, for now, a cut down omega... -
S
THE TM MWS thread
You were as shocked as me? Defcon also have the mags in stock at £50 -
S
THE TM MWS thread
Hi @Davegolf fully understand that. Thank you, I’ll wait for your reply from your website. I’ve only had my MWS a couple of weeks but this thread made my mind up. I can say to anyone that even stock, the MWS has renewed my love of airsoft. It is so satisfying. FYI - wolf armouries has a few... -
S
THE TM MWS thread
@Wo1f Thank you so much for starting this thread. So much info, looking forward to taking my MWS out as soon as lockdown is over! @Davegolf Are you still making the brass nubs?
