• Hi Guest. Welcome to the new forums. All of your posts and personal messages have been migrated. Attachments (i.e. images) and The (Old) Classifieds have been wiped.

    The old forums will be available for a couple of weeks should you wish to grab old images or classifieds listings content. Go Here

    If you have any issues please post about them in the Forum Feedback thread: Go Here

Recent content by JoeTheBane

  1. J

    MP5 Push Pin

    Hi I have a gsg 522 mp5 SD, basically a ICS mx5 sd. I have lost the middle push pin between the trigger and magazine well and cannot find where to buy one online. I have also lost the metal inner cylinder that the rear pin fits into on the stock. Many thanks
  2. J

    Replacement m100 spring a lot stronger and a longer than current

    I couldn't even compress it into the gear box, I'm not weak by any means but it was way too long and strong to compress into it.
  3. J

    Replacement m100 spring a lot stronger and a longer than current

    hi I ordered a shs m100 spring to downgrade my mp5 to less than 350fps, only to find the current spring is shorter and weaker than the new m100. How would the fps be downgraded with a stronger longer spring? Maybe the spring was mislabeled? I dont have a chrono to test the fps, so i only really...
  4. J

    A few issues, inconsistent and high fps + bbs dripping right

    Ok thanks, I've ordered a new buckling and a shs m100 spring, hopefully I'll be getting more accurate shooting with consistent fps :)
  5. J

    A few issues, inconsistent and high fps + bbs dripping right

    I found the nub, tricky thing to put into its hole haha, also theres a small mound on the inside of that clear rubber, the mound is pretty much ruined, missing chunks in it. I assume replacing that clear rubber with something like this...
  6. J

    A few issues, inconsistent and high fps + bbs dripping right

    Theres a little rubber seal that was on the barrel - http://imgur.com/a/GFXAH its looks quite old, worth replacing the entire unit?
  7. J

    A few issues, inconsistent and high fps + bbs dripping right

    http://imgur.com/a/0OZoi Images of the barrel and hop up unit
  8. J

    A few issues, inconsistent and high fps + bbs dripping right

    Hi I went skirmishing yesterday and chrono'ed my g&g 522 using .2g BB's (BB king) and they were consistent 346fps area, then for the official chrono done by the marshals using blaster devil .2g the fps shot up to 360fps. Also the bb at a distance of around 30m+ they dip and drift to the...
  9. J

    Rough FPS for GSG MP5 522?

    I got it chrono'ed at my local site and it shoots under the limit at 347fps, phew :)
  10. J

    Rough FPS for GSG MP5 522?

    Ok great, thank you for your help!
  11. J

    Rough FPS for GSG MP5 522?

    Ok, so a spring swap is a must, I don't want to get turned away from the site, that would be embarrassing haha. So what spring model would I need, m'something' 90,100? I would like to be as close to 350fps and but remain under it. Thanks!
  12. J

    Rough FPS for GSG MP5 522?

    Just asked him today and he said there's an American version that does near 400fps and his does around 360 fps, would I be let in with 360fps? Just over the limit. How about offering to run with heavier BB's to reduce fps?
  13. J

    Rough FPS for GSG MP5 522?

    Hi I'm new to air soft and this will be my first gun, its a gsg mp5 522 with suppressor, new barrel fitted that goes to the end of the suppressor. What would be the rough fps on this gun? I've seen vastly varying numbers from over 400fps to just under 300pfs. Local site limit is 350fps with .2g...
See more
Back
Top