• Hi Guest. Welcome to the new forums. All of your posts and personal messages have been migrated. Attachments (i.e. images) and The (Old) Classifieds have been wiped.

    The old forums will be available for a couple of weeks should you wish to grab old images or classifieds listings content. Go Here

    If you have any issues please post about them in the Forum Feedback thread: Go Here

Recent content by JME

  1. J

    M14 Hop-up Bucking for a DMR Build

    Don’t worry about the last message. I found a ZCI 550mm 6.02 Stainless Steel Barrel from the states for £19 ? couldn’t say no to that. 
  2. J

    M14 Hop-up Bucking for a DMR Build

    Has anyone heard about these barrels? https://www.onlyairsoft.com/product/laylax-prometheus-eg-barrel-for-m14-excl/   im trying to keep to the 500mm area as the stock one is 570mm on mine. I found these barrels
  3. J

    M14 Hop-up Bucking for a DMR Build

    Ahah yes I do have some spare, I believe you recommend these in particular before. I’ve got the tan ones, 60 degrees I believe.  I’ve decided just to keep the stock barrel. I’m having a hard time finding a decent M14 barrel long enough. Lots available for the socom but I like my long barrel...
  4. J

    M14 Hop-up Bucking for a DMR Build

    I’m making a DMR on a budget. And I know even though it’s on a budget it still isn’t cheap. I’ve chose a CYMA M14 CM032 (Long) and I've read they have really good accuracy out the box.  The hop up bucking that comes with the gun seems to be able to handle 0.43g bbs which I will be using on game...
  5. J

    Cyma M14 low fps

    Hiya how did it feed in the end. I read the O ring nozzles are for TM M14s and the CYMA takes slightly different nozzles. I read it requires removing some material off the sides to fit in the gearbox and still move? Apart from that’s bit, more importantly; does it feed ok? Is it not too long or...
  6. J

    Cyma Ak47 Stock

    I will try this. The AK was intended to be a back up gun to my VFC M27 (416). But today I couldn’t use the HK M27 so I used the cyma ak. the M27 hop up is far too tight. Even when the hop is on the lowest setting the gun over hops and misfires and two bbs come out on the next shot, and when the...
  7. J

    Cyma Ak47 Stock

    It turns out the hop up was on full. When off it runs 335 so that was one of the issues. Thank you 
  8. J

    Cyma Ak47 Stock

    So to get a better seal I put some molly grease in the cylinder and around the piston o ring. I’m getting a consistent 290fps. I’d like it to be a bit higher. The compression felt good when I applied the grease. I wasn’t comfortable skirmishing with 215fps but maybe I might give this gun a game...
  9. J

    Cyma Ak47 Stock

    I messed around with the motor adjuster screw and it seems ok
  10. J

    Cyma Ak47 Stock

    all the information has been really helpful. I’ve taken everything apart and cleaned and relubed it and I feel comfortable doing it again. I have one issue and it’s when I do put the pistol grip. If I do it up so the screw is secured the motor locks up. This might not be the motor but the gun...
  11. J

    Cyma Ak47 Stock

    Piston o ring seems baggy. Is this normal and nozzle has ptfe tape over the o ring?? Any expert comments on this and will this be the cause of low 200fps? thank you.  ...also, is this a mosfet?
  12. J

    Cyma Ak47 Stock

    So can it be a bit trial and error finding spares and replacements? 
  13. J

    Cyma Ak47 Stock

    I’ve come from airguns and firearms and I’ve found airsoft is completely different to both. I need to be able to understand what gun takes what parts and what parts with fit my guns as I assume they’re not all compatible 
  14. J

    Cyma Ak47 Stock

    Thank you!!! Thoes link actually are really helpful. Being new I don’t even know what to look for or where to look. 
  15. J

    Cyma Ak47 Stock

    Air seal meaning the nozzle and hop up seal? Sorry I’m new to all this all this information is extremely helpful 
See more
Back
Top