• Hi Guest. Welcome to the new forums. All of your posts and personal messages have been migrated. Attachments (i.e. images) and The (Old) Classifieds have been wiped.

    The old forums will be available for a couple of weeks should you wish to grab old images or classifieds listings content. Go Here

    If you have any issues please post about them in the Forum Feedback thread: Go Here

Recent content by dazz

  1. dazz

    Well L96 Internal Upgrades

    My two pence worth.... Assuming you want your L96 based rifle to be firing close to 500fps as possible... You'll end up spend around the same on a Well L96 and the TM L96. With the TM L96 AWS, currently, the best option (if i do say so myself) is to go down the PDI route. So, sears, piston...
  2. dazz

    Silencer Thread Question for Warrior L96

    http://www.airsoftsniperparts.com/apps/webstore/products/show/2697655
  3. dazz

    TM VSR vs Well L96

    has anyone tried ASPUK parts?
  4. dazz

    TM VSR-10 Pro Upgrades

    You also now have the option of parts available from ASPUK. www.airsoftsniperparts.com - if you have any questions get in touch.
  5. dazz

    Well L96 Internal Upgrades

    dont want to leave this thread unanswered..... Ideally, your L96 should have it's piston, spring guide and cylinder replaced if you're going to run over 450fps. Cylinders on the new models are thinner and weaker than older versions, simply putting a high tensile spring will snap your cylinder...
  6. dazz

    ARES MSR MS338 / MS700

    https://www.facebook.com/media/set/?set=a.529967660399040.1073741836.176087792453697&type=3
  7. dazz

    ARES MSR MS338 / MS700

    I've seen many posts regarding the ARES MSR and thought i'd share my story. I picked up an MS700 in a swap. The rifle was fine, no slam firing issues. The fps was 380 on a 0.2g bb so this led me to start thinking about upgrading. I run ASPUk so i'm pretty clued up on spring sniper rifles. When...
  8. dazz

    Well L96 Internal Upgrades

    just an update as i get a lot of queries from this thread. be aware of L96 cylinders. All the newer versions are using weaker cylinders. In the past stock cylinders could handle upgrade springs but over the past year or so, to save costs, L96 rifles have got slightly thinner aluminium cylinders...
  9. dazz

    Are these parts VSR/APS2 compatible?

    Righto, looking at the photos and off the top of my head measurements.... Looks like it takes: VSR Piston Sear VSR Trigger Sear (need to confirm length to see if its the same as VSR or the longer version in TM L96 AWS) Cylinder Head Piston Spring Guide Set Pin - although located in a...
  10. dazz

    VSR-11 Upgrades

    Just to confirm (necro post here sorry) - Then HFC VSR-11 is fully VSR compatible.
  11. dazz

    Well L96 Internal Upgrades

    ASPUK have an offer on at present for L96 upgrades! See http://www.airsoftsniperparts.com/apps/web...y/639220?page=1 Or, as we're unbiased, you can visit PDIs type96 section, http://www.x-fire.org/etop/t96.html
  12. dazz

    Snow Wolf M24 - PDI/Laylax Compatibility

    there are two versions of the SW M24. One based on the VSR trigger mech and the other APS2 Type96. I have worked on the APS version and coan confirm........ It takes APS2 Type96 (MB-01) spring guides, piston spring. The piston sear is also compatible but the trigger sear is unique. The hop is...
  13. dazz

    well mb01/mauser sr upgrade advice

    eekk dont use it. i've had loads of people come to me after trying this. Most have issues with the cylinder, the measurements are often wrong! Stick to Laylax, PDI, Guarder or ASPUK! In this instance, you get what you pay for!
  14. dazz

    Well MB-01 (L96) Version 3 Review

    be very wary of that kit from airsoft club. i was very tempted myself. i chap from ireland contacted me after he tried the kit. The cylinder was slight;y wrong measurement, piston grated and a few other problems. the chap bought from us and had no issues. Now im not suggesting to not buy this...
  15. dazz

    ARES SVD-S Compatibility Q's

    A&K are clones of King Arms (AtoZ) The pistons will fit in the ares along with the sear which u have to drill a small hole underneath for the piston spring to sit in. Hops are unique!
See more
Back
Top