• Hi Guest. Welcome to the new forums. All of your posts and personal messages have been migrated. Attachments (i.e. images) and The (Old) Classifieds have been wiped.

    The old forums will be available for a couple of weeks should you wish to grab old images or classifieds listings content. Go Here

    If you have any issues please post about them in the Forum Feedback thread: Go Here

Recent content by Dan

  1. D

    Ics m4a1 barrel nut and rails

    Hi does anyone know of a keymod handguard or possibly a wire cutter handguard that will fit on an Ics m4a1 preferably not overly expensive?   fire support sell the Ics Keymod system but it's £111 I'm not overly fond of spending over a ton on a rail for my m4 as I didn't pay much more for the gun...
  2. D

    Marui m&p 9 parts

    Anyone on here know where I can get a licensed metal slide and metal outer barrel for my marui m&p 9 , that's not an enormous amount of money. preferably same as stock one but metal with no fancy cutouts cheers.
  3. D

    £300 budget for new gun?

    I would go for an Ics par M3 or Cxp UK1r both a tad over £300 but seem to be quite good, I wanted one of the above but my budget was lower due to having a baby and missus would be tapping her foot :P so went for and Ics m4a1 instead  think most of them come with two hi caps too .. 
  4. D

    How to increase range in a sniper?

    Wouldn't touch the spring as internals are plastic ( unless you up grade) but can cost more that the gun as Iv got a one myself and the sears would need doing. Just put a decent hop rubber and maybe a better barrel. fps isn't range at such it's just the speed / energy of the bb. It might giv you...
  5. D

    The 'What have you just bought' Thread

    Tan Ics m4a1 awaiting delivery , kryptek mandrake top/bottoms/hat bout month ago...  couple of h nubs and a set of magpul style flip up sights :)
  6. D

    Good sniper to start with

    Depends on your budget there quite a few out there 
  7. D

    L96 hop up help

    Ok so done ptfe tape on the airseal in the cylinder and hop. also done the tooth floss mod on the bucking and ended doing the Biro mod as a nub and electrical tape for a barrel spacer however the constancy is still poo but the gun has more power so will have to get hold of some .36 or higher and...
  8. D

    L96 hop up help

    Yer I will , as for the barrel spacers might be a pain as its got a flutted outer barrel which is tapered lol so that will take a few goes 
  9. D

    L96 hop up help

    I didn't think so :/ I'm guna try a couple of different things , Biro, eraser and see what else works I think 
  10. D

    L96 hop up help

    This is mine atm
  11. D

    L96 hop up help

    Ok how much you wanting ? And you got a picture ? 
  12. D

    L96 hop up help

    Ok nice one I will have a look and see what results I get will let you know how I get on 
  13. D

    L96 hop up help

    Yer it's stock done an air seal mod with ptfe tape on the cylinder thread and where the hop rubber meets the barrel and it slowly decreases with my finger over the barrel but where the nozzle meets the hop air escapes so guna buy a better cylinder head and hop rubber soon just need to sort this...
  14. D

    L96 hop up help

    Forgot to mention I'm running it with lower power than most it's about 370 fps with .2 but I'm using .3 as my go too weight so don't need a stupid amount of hop as it would be too much 
  15. D

    L96 hop up help

    Yer ok mate nice one 
See more
Back
Top