• Hi Guest. Welcome to the new forums. All of your posts and personal messages have been migrated. Attachments (i.e. images) and The (Old) Classifieds have been wiped.

    The old forums will be available for a couple of weeks should you wish to grab old images or classifieds listings content. Go Here

    If you have any issues please post about them in the Forum Feedback thread: Go Here

Recent content by CzechMeOut

  1. C

    40mm Grenades not releasing all their gas properly

    Hello, So I seem to have solved this. I had everything greased up but after stripping, cleaning everything off and only greasing the 2 o-rings on the plunger (that also holds the ball bearings) the grenades are now firing with a big singular bang!
  2. C

    40mm Grenades not releasing all their gas properly

    I have a couple of ASG 40mm shower shells that both aren't releasing their gas fully in one go, as the video shows. They did used to work (over a year ago probably) and I've tested on a couple of different launchers along with making the firing pins way longer than they need to be. I'm...
  3. C

    JG G3 Bent Barrel

    No it's definitely the barrel. Looks like the previous owner may have took a tumble and bent it.
  4. C

    JG G3 with 3D Printed Wood Furniture

    Purchased as a project for £50. I've 3D printed some wood furniture for it and I'm mostly happy with how it turned out. Printed in walnut 30% wood PLA, 1 coat of walnut wood dye and 1 coat of teak wood varnish.  Internal upgrades: - Perun V2 - Maple Leaf 70 degree rubber - Tomtac 6.02...
  5. C

    JG G3 Bent Barrel

    Purchased a JG G3 as a project for £50. I've upgraded it and it's brilliant (rock solid gearbox!). Only issue is the barrel is bent to the left. The inner barrel is fine (I've actually replaced it) but the outer barrel is bent to the left. Still getting consistent 430fps (DMR) and groupings...
  6. C

    MP5K Loose Body Pin

    So I had a magazine adapter jam inside the magwell of my CYMA MP5k. Removed it but now the body pin is very loose which it wasn't before. The little brass cyclinder that goes through the mag release catch falls out when it never did before. I can put it all back together OK and the mag...
  7. C

    Fitting mosfet to JG MAC10. Where to solder trigger contact wires?

    I have a Jefftron Micro mosfet I want to fit to my JG MAC10. Could anyone point me to where the trigger contact wires should be soldered to? Also I'm OK to get rid of the original fuse as the mosfet will replace it's function correct? Thanks!
  8. C

    Ares Vz.58 Upgrades

    Little update. I swapped to a Rocket M105 spring and it's now shooting at 315fps with a 0.25 and no hop up. Rate of fire is 34RPS according to my chrono!
  9. C

    Ares Vz.58 Upgrades

    Hey thanks for your detailed reply! I ended up putting in a new hop up rubber, M110 spring and 12tpa high speed motor. The air seal is better than I assumed as it's now over the limit at 380fps 0.2 and 350fps 0.25 with no hop up. FPS is only varying by 1-3fps per shot which I assume is pretty...
  10. C

    Ares Vz.58 Upgrades

    Hello, I have recently acquired a well used Ares vz.58 Long rifle. While it's working OK, it does feel a little weak (no chrono atm) so I'm looking to upgrade the internals but I am totally new to this. So far based on my research I have bought the following parts: - M110 non-linear spring -...
See more
Back
Top