-
PXL_20260328_113708188.webp -
PXL_20260328_113733704.webp -
PXL_20260328_113922126.webp -
PXL_20260328_113934794.webp -
PXL_20260328_114044544.webp -
PXL_20260328_114130970.webp -
PXL_20260328_114306193.webp -
PXL_20260328_114341088.webp -
PXL_20260328_113332231.webp
- Condition
- Used
Selling off some MWS bits that have been gathering dust since moving away from the platform
Original Tokyo Marui Upper Receiver with 10.3 inch TM outer barrel: £200-250
Vortex Viper 4-16x44 Scope: £460
Madbull Carbon Fiber round handguard in black. Unfortunately rare, the closest I can find is the tan version here for £460: https://airsoft-shop-japan.com/madb...ound-rail-12-5-carbon-fiber-tan-p01-006tan-c/
Madbull full length top rail for MK12: £95
Airsoft Artisan PRI gasbuster charging handle for MWS with trades: £40
A&K MK12 rear sight with Guarder #40 fixture latch for picatinny, otherwise the A&K strips its threads immediately: 55 + 15 = £70
Maple Leaf inner barrel sized to match the outer barrel length perfectly: £40
Laylax Strike Arm: £20
Genuine Butler Creek scope caps: £30
Airsoftglobal MK12 ARMS style scope rings with top board: £30
Cyma front sight and repro CQD sling mount: £20
Gas tube with fitment insert in receiver end: £20
Outer barrel sections drilled with detent for muzzle collar: £20
Z Parts Suppressor and muzzle device kit: 65 + 45: £110
(Bipod not included)
Total price new around £1600, with large parts like the handguard no longer being available
Lockup on everything is solid and tight. Barrel has been drilled to half depth with a detent to lock the suppressor collar down without pressing against the front sight and causing damage.
Scope is perfect for the setup, with non locking non covered adjustment dials and butler creek scope caps to fit the original vibe.
Handguard is carbon fiber with a moving end piece to prevent damage. This is the older generation of handguard that was commonly used in GWOT, not the less common newer variant that is currently being manufactured by VFC.
Barrel is 1x section on the end with the front sight and muzzle device pairing, and then a 2 inch section between this and the TM outer barrel to swap between the full length and the Mod H length if desired, without needing to change the muzzle device. Flash hider is shimmed rather than washered, because the extra tension is required to get good lockup with the suppressor.
Has had a few games so it has a bit of cosmetic wear. I use it with .36's and the hop has room to spare for heavier if the gun is used at DMR FPS. Hop performance is consistent and accurate.
Price is £800 with postage included, paypal G&S
Willing to discuss part trade for RS parts such as M203 handguard or RS Elcan Spectre
Original Tokyo Marui Upper Receiver with 10.3 inch TM outer barrel: £200-250
Vortex Viper 4-16x44 Scope: £460
Madbull Carbon Fiber round handguard in black. Unfortunately rare, the closest I can find is the tan version here for £460: https://airsoft-shop-japan.com/madb...ound-rail-12-5-carbon-fiber-tan-p01-006tan-c/
Madbull full length top rail for MK12: £95
Airsoft Artisan PRI gasbuster charging handle for MWS with trades: £40
A&K MK12 rear sight with Guarder #40 fixture latch for picatinny, otherwise the A&K strips its threads immediately: 55 + 15 = £70
Maple Leaf inner barrel sized to match the outer barrel length perfectly: £40
Laylax Strike Arm: £20
Genuine Butler Creek scope caps: £30
Airsoftglobal MK12 ARMS style scope rings with top board: £30
Cyma front sight and repro CQD sling mount: £20
Gas tube with fitment insert in receiver end: £20
Outer barrel sections drilled with detent for muzzle collar: £20
Z Parts Suppressor and muzzle device kit: 65 + 45: £110
(Bipod not included)
Total price new around £1600, with large parts like the handguard no longer being available
Lockup on everything is solid and tight. Barrel has been drilled to half depth with a detent to lock the suppressor collar down without pressing against the front sight and causing damage.
Scope is perfect for the setup, with non locking non covered adjustment dials and butler creek scope caps to fit the original vibe.
Handguard is carbon fiber with a moving end piece to prevent damage. This is the older generation of handguard that was commonly used in GWOT, not the less common newer variant that is currently being manufactured by VFC.
Barrel is 1x section on the end with the front sight and muzzle device pairing, and then a 2 inch section between this and the TM outer barrel to swap between the full length and the Mod H length if desired, without needing to change the muzzle device. Flash hider is shimmed rather than washered, because the extra tension is required to get good lockup with the suppressor.
Has had a few games so it has a bit of cosmetic wear. I use it with .36's and the hop has room to spare for heavier if the gun is used at DMR FPS. Hop performance is consistent and accurate.
Price is £800 with postage included, paypal G&S
Willing to discuss part trade for RS parts such as M203 handguard or RS Elcan Spectre
