Jump to content

The AAP-01 Owners Thread.


Cr0-Magnon

Recommended Posts

17 minutes ago, AlphaBear said:

Chaps that black mamba kit specifies a type A and type B kit? What’s the distinction between the two?

 

ta 

Texture on the receiver sides, can't remember which one has them though

Link to comment
Share on other sites

6 hours ago, AlphaBear said:

Chaps that black mamba kit specifies a type A and type B kit? What’s the distinction between the two?

 

ta 

Looks to be just aesthetics from what I can see. A bit more texture under and around the top rail.Screenshot_20210225-012228.thumb.jpg.a8dc34349c7d0b1447d7d057b0a7c884.jpg

Link to comment
Share on other sites

80psi and with 0.25g BB's I'm getting between 280 and 296 with around 293/295 the most common. Hop is not set as I don't have the range so need to factor that in a bit but not too shabby. Puts it very near the 1J marker I "prefer" to play with indoors. Expecting the PDI barrel to nudge it over which sits it squarely in the same region as my capa's.

 

The upgraded nozzle valve spring should calm that variation down a bit as well. Ran a couple of mags through, doesn't feed quite as nicely as my capa setup does but it does enough and they are dinky cheap little mags not the Ares 140's i usually play with.

Link to comment
Share on other sites

4 minutes ago, Steveocee said:

80psi and with 0.25g BB's I'm getting between 280 and 296 with around 293/295 the most common. Hop is not set as I don't have the range so need to factor that in a bit but not too shabby. Puts it very near the 1J marker I "prefer" to play with indoors. Expecting the PDI barrel to nudge it over which sits it squarely in the same region as my capa's.

 

The upgraded nozzle valve spring should calm that variation down a bit as well. Ran a couple of mags through, doesn't feed quite as nicely as my capa setup does but it does enough and they are dinky cheap little mags not the Ares 140's i usually play with.

 

I have a daft question to ask here.... how do you know what PSI you're getting? Unless you're HPA'ing (is that even a word?) the pistol I hazard to guess?

Link to comment
Share on other sites

2 minutes ago, AlphaBear said:

 

I have a daft question to ask here.... how do you know what PSI you're getting? Unless you're HPA'ing (is that even a word?) the pistol I hazard to guess?

 

Primary Glock>M4 HPA adapter arrived earlier today. 80psi is about that of the weaker duster gas, 110psi is touted as green gas but as our climate is fairly cold we rarely see above 90psi from our green.

Link to comment
Share on other sites

Ahhhh I see what you mean now. Gotcha. My gas knowledge is limited to Abbey Green, Abbey Ultra Predator (Red can but still classed as Green) and Nuprol black which I dare not try in this pistol. 

Link to comment
Share on other sites

IMG_20210228_211215__01.thumb.jpg.15a2709e8e0cf7492e02d7ca16ed3b32.jpg

 

Well look what I collected today!

 

Just had a quick test fire. 1 full gas fill on nuprol green that's been kept near the tumble dryer has chucked 1.5 drums worth of BB's so far I reckon. A mixture of semi and full auto firing.

 

It's a weighty beast but with the stock on and holding my left hand around the torch it feels well supported and near enough centred.

 

I'll hopefully have a play in the day time and record some footage after I've taken the kids to school this week!

Link to comment
Share on other sites

1 hour ago, Steveocee said:

Think this'll ruffle some feathers of people who wear Crye everything and call each other by callsign.

krEVmbGMsGQrZ7QVzwLLZdiXwZhFPaPRkxW-xn60DnfA0k9aOJMHz_d6YLcx7tSWwbkTAhTmkUDT2Q3YaAu3DE6AM5bmMH0LieLVdtN59qVDDXa-DTd20t8buaEUGZWjCfTDGr0CTKGElGmFRh-r-kbmxbHE7IGt0z6up-lUnUI6DxwtcqhCOj0GjOXg4AwUt7KSEtHBaE0esUb1DvJ9hgq-SBx-fb68wL3fGeYbp_mtg-G9kTVPHq0uVSxrJv8Ab3ltvF8MOBgdJKp449zTuBAtAHl6QI2nkgU30SQlosJDCiXSEqkwu_GE2tpque5Zi_9hnfI5fUqcbVcjRPR7W6TkLx9amrAVLf956KdGFh4viF-L3D7MseGEDruILs0clVRfUKK3yUkTSI7Vx9dety89b8WEGey_c-61-7xy8ze27759oERajkbyrq02KIm6P3Vkj8Mop7w0QauFK6NehXwhnmUGcKGxxRUYh08jDsvqvlNWzbENkTBbwSd_A-VukYY8TDJBPyE9ExRC8TjRQ43nh9OdSud34f7sXKnSL__I4ii5GomMh5jA2DwXbj2hHMrQiGpJ3hOSUaQlChWrd2Nn2f613dg-_OMXC42gwsB3pxvC6CHZuTPONHo9JlifvhdGqkCTrljBcwifUX5XmeZvXU_zpkUAy1anlsym4sfs16v2EQTaMqZeM5WvRQM=w1508-h1128-no?authuser=0

 

Obviously the power cord takes away some realism but I can appreciate that this is a tool optimised for CQB use.

Link to comment
Share on other sites

10 hours ago, leadly said:

IMG_20210228_211215__01.thumb.jpg.15a2709e8e0cf7492e02d7ca16ed3b32.jpg

 

Well look what I collected today!

 

Just had a quick test fire. 1 full gas fill on nuprol green that's been kept near the tumble dryer has chucked 1.5 drums worth of BB's so far I reckon. A mixture of semi and full auto firing.

 

It's a weighty beast but with the stock on and holding my left hand around the torch it feels well supported and near enough centred.

 

I'll hopefully have a play in the day time and record some footage after I've taken the kids to school this week!

 

Now this is looking pucker! The post-mid-life-crisis part of me is liking this!! I wonder if they make that stock extension in FDE otherwise it will be Krylon.. (meh).

 

So one gas fill is enough for about 500bbs? That's impressive. So how much gas do you reckon get's pumped into it?

Link to comment
Share on other sites

1 hour ago, Cr0-Magnon said:

 

Obviously the power cord takes away some realism but I can appreciate that this is tool optimised for CQB use.

 

Very much so. I fancied a parrallel path to my Hi Capa. For outdoors I have an SRS sniper and a G&G SRS P* although I am tempted to try the AAP in a few "closer range" outdoor scenarios.

FiBsCCVxkm0OgBIyXAOqWmFOxRe1u7jVhOSB9P7ZwEtYY7N2RWqLi-_JKqQtlVY04vDpMZSS4ryCIkAK1YNleu9CZfhEcKaWCmP-snClR2x6K3hpWbl0jOUzEXWsjNoUQvIM5S3ZOKxj0BglPz3dsmNaiCusahgZe0OpN4zhIok69MUP-WFwgjVW4n0FW19oYR9MqFtb4P7KwLaY387QDoA-AB4FIW1qhYi9n7h4gSr3E_oPa9xLNsazWKoXeLGOLvJqQA0aOxL9PVWe8-Qk0QwtrYDWWBKjBWVZYKHmd7Ukiod0vHqWAPG4im2D0t3ACuu46-1JkMP6DxWM5gNkcymbIuZVGHUV1M2hSG7iIJZ1_AyF69cPOlJ_KK9wRxx75LGw7TsMrpyfdwsqfF_aes0JTtAIXQ-HV02Zrb8obFr0SZbryAyfphtuJK8zOjpMfdt_jnweJoeR9mT6-0D0lmLZz83299LjNlyL_-hIjqsD6J0NPVbYGnM9YRPa5uc8-uODYpR8dyR0YxQzUGT3rhNvXMy7FK4xv36-38I1c6v53GKAo2zg_U11RlmxTL-r0BujNK1TKIzXNVOsMsX3RjxXiggCxlYdVRvGV2McdmBFIEsc4xJixlmZtR9Y6IbnmuzCFiW3Won8ALlKJsqbnc1PxSdFdyHPJd9DHx8xsUdUe7PYBzOmiIUhuOdpgQA=w1508-h1128-no?authuser=0

Link to comment
Share on other sites

PDI barrel arrived this morning. What a beauty she is as well! Even has the oring at the end to ensire it's centered correctly and ideal length of 129mm. Strange how the ZCI was only 1mm longer but seemed to sit so much further forward. Anyway, installed it this evening and couldn't help but do a quick test fire. Again at 80psi I was getting roughly 300fps with a 0.25 which is about perfect for what I want.

 

vWoCkEIu7HHl6YhttuLrBbszX2_MMfu3cyONDLRFyARXOU2vw6eZkM_CIfiTDMpeXfWFHWOVvnnvTB5wRah6LtAAsjoowFk1N_P7N0A2v4-5qdRltKXubWNbTf_15v97QrbN2m4_uQ_5RX_rtgYlRF8noJ6KdjSFzusFwshhXmOH27mbw48DR1XClmdfDQwO_uTlLLgs28Ju4LqWt4VOdn6I_V1BkKLWg34kpgldFskgolGuhxdoZ8BQAhSHSO4cMVS6zi8pxlODxF2Q_1vtSSss8SRGz-W9mj6B8wlOM6E3HW9uYFDsDQy-Rmn293j_QsSfJHi7Oj8mTN_9UMIRol4TafBBK4HfMdq7gOA3SZR2J5o7PWOE1mc2WZpaplVXV-EnZw3WIDPhT_HfZ_0-Tu1WT7D7Jov1IwzevR8qY9uldoVFvI3XGvwzEUhIPuRKCnWXZac92Nr7trtRsEPxpR8F4iMiN061iIYlSoAtzCjK0UJAMXEqztgukvKkvuXlM9lEvT7wbYGD5jA3PQKIF49lUf6DDAgBVhWmxAZBHi-UfBP7rAx7_KYF9tq-HccLzv9SxU9uXdrDVUuQR7girgp8XwK90X4v9RElg5cOUJB1SKtJhyPC7SBO32n-K6DmQA3Wv4eaPFRyijF_4ZxaHH0mE3hk7bctKXlqXhIM4QBd92QdGjuiCySFW9LjMc8=w1160-h868-no?authuser=0

 

I have noticed though a fairly bad feeding problem only getting about 1 in every 3 or 5 shots a BB comes through.

When I strip down for the nozzle valve spring I'll look into this more closely but did also notice the flow valve in the mag is leaking as well so that's going to get pulled out, lubed and then likely upgraded.

 

 

Link to comment
Share on other sites

11 minutes ago, Steveocee said:

PDI barrel arrived this morning. What a beauty she is as well! Even has the oring at the end to ensire it's centered correctly and ideal length of 129mm. Strange how the ZCI was only 1mm longer but seemed to sit so much further forward. Anyway, installed it this evening and couldn't help but do a quick test fire. Again at 80psi I was getting roughly 300fps with a 0.25 which is about perfect for what I want.

 

vWoCkEIu7HHl6YhttuLrBbszX2_MMfu3cyONDLRFyARXOU2vw6eZkM_CIfiTDMpeXfWFHWOVvnnvTB5wRah6LtAAsjoowFk1N_P7N0A2v4-5qdRltKXubWNbTf_15v97QrbN2m4_uQ_5RX_rtgYlRF8noJ6KdjSFzusFwshhXmOH27mbw48DR1XClmdfDQwO_uTlLLgs28Ju4LqWt4VOdn6I_V1BkKLWg34kpgldFskgolGuhxdoZ8BQAhSHSO4cMVS6zi8pxlODxF2Q_1vtSSss8SRGz-W9mj6B8wlOM6E3HW9uYFDsDQy-Rmn293j_QsSfJHi7Oj8mTN_9UMIRol4TafBBK4HfMdq7gOA3SZR2J5o7PWOE1mc2WZpaplVXV-EnZw3WIDPhT_HfZ_0-Tu1WT7D7Jov1IwzevR8qY9uldoVFvI3XGvwzEUhIPuRKCnWXZac92Nr7trtRsEPxpR8F4iMiN061iIYlSoAtzCjK0UJAMXEqztgukvKkvuXlM9lEvT7wbYGD5jA3PQKIF49lUf6DDAgBVhWmxAZBHi-UfBP7rAx7_KYF9tq-HccLzv9SxU9uXdrDVUuQR7girgp8XwK90X4v9RElg5cOUJB1SKtJhyPC7SBO32n-K6DmQA3Wv4eaPFRyijF_4ZxaHH0mE3hk7bctKXlqXhIM4QBd92QdGjuiCySFW9LjMc8=w1160-h868-no?authuser=0

 

I have noticed though a fairly bad feeding problem only getting about 1 in every 3 or 5 shots a BB comes through.

When I strip down for the nozzle valve spring I'll look into this more closely but did also notice the flow valve in the mag is leaking as well so that's going to get pulled out, lubed and then likely upgraded.

 

 

I assume the barrel doesn’t stick out of the front end right? I mean protruding more than the outer barrel. Oh you all know what I mean lol

Link to comment
Share on other sites

1 hour ago, AlphaBear said:

I assume the barrel doesn’t stick out of the front end right? I mean protruding more than the outer barrel. Oh you all know what I mean lol

Correct. Stock barrel is 129mm from what I can find and PDI have copied this, you can get away with a 130mm but I wouldn't want anything more without a suppressor or tracer.

Link to comment
Share on other sites

I'd be interested to hear how much difference in accuracy of groupings the PDI barrel makes over the stock barrel... I appreciate it's a pistol and not an AEG length barrel and in addition I guess you need to have an appropriate distance to test over say 30m-40m? I mean what's the general expectation of this pistol? It's not gonna be MK23 type level but would still be interesting to know what to expect.... 

Link to comment
Share on other sites

13 hours ago, Steveocee said:

Correct. Stock barrel is 129mm from what I can find and PDI have copied this, you can get away with a 130mm but I wouldn't want anything more without a suppressor or tracer.

Have a look at my earlier pictures. This has the PDI MK23 barrel which is 133mm long. Without the compensator on the Mamba upper or the thread protector on the standard receiver you can just see the end. With the mamba compensator it is fine. With the thread protector only it protrudes about 1mm.

 

113138899_app-01innerbarrel.thumb.jpg.56cda1da9e2f20b9e6a7caddb60e41ba.jpg

Link to comment
Share on other sites

On 01/03/2021 at 02:27, AlphaBear said:

 

Now this is looking pucker! The post-mid-life-crisis part of me is liking this!! I wonder if they make that stock extension in FDE otherwise it will be Krylon.. (meh).

 

So one gas fill is enough for about 500bbs? That's impressive. So how much gas do you reckon get's pumped into it?

not trying to one up but I am going to 

20210304_131109.jpg

Link to comment
Share on other sites

Installed the charging ring and flared magwell last night. removed a short stroke and I think it just about solved the feeding issues. Bit low I can only use 1 buffer but to be fair it's plenty fast enough as it is anyway. got a bit of an issue in that the primary adapter doesn't fit with the magwell so need to "adjust" one of them but not sure which. Any ideas?

422XY9Kr-pP1f-Lp4A7Bgdcdg_PhiZAl_y6VqQqAb3OCIBceNJHA7_sv9FgkvDU_pb0VQIGlgYagdIs4u0YXwY_kVpPtsPBuPSACHOvqKn9u8Vp-YReqn44KGppY-9xcaNgwdalwtuZZSEkw9XY3tRZjfJ1ZNEBylYQuJ5kKSrAUk35Y1ASZhIzetZgdxtXiCTT01pE5qGvyURyVY5V-P69ZuF2DRNMILIi2AT70IXlW6SPp1uDwQWVmMJWDNEy-84GwY6huvFkXcnqSSt0b9kgBoEBwgKY3fiItVuBp3kti96On27i6Kc94ki-ZH8LUwh74fJOUuyBHux9A6B_HvmQd0z5BQicrZFW6DIY50I-Fcc2-yM7J_gOpQyOpvyzct-RqLKf3JhMJS2x-CDLkcuMsC2FkJdwEZepJqcY47OyL1w2bLJBXj6JGrqpsfB83Hd719kM27bCPB-HXZuX8Fj-zQkm3gxc_wPjWTBTuCLVCI7NKn8_GWP0WqsJOlwk-TaFsBq2Qxdz_4fAclpI8hVXJ9jl0M1we2M9I3VVqOZQLyQEum4ES7XNbjJEdjfleRpbnwj7kEUdRnl0Xu_jNLBG5I3Ra9sZ5R6xpEe9h5toalh7Wq20SWm-qGAy5XzkHDVIK3zkVBH6lYHiH9mFWFx1Z4SmKXE6A1nS3eaJQGKzPDdWc9V4vlRq3DvZqHDA=w1162-h869-no?authuser=0

Link to comment
Share on other sites

Magwells seem to be an issue for people running HPA taps or drum mags, most people just don't use them.

 

If it's a small amount of material that needs to be removed, I'd say go ahead and dremel the crap out of it (magwell, wouldn't touch the adapter).

Link to comment
Share on other sites

13 hours ago, Brett248 said:

not trying to one up but I am going to 

20210304_131109.jpg

 

Once I've ran out of green gas I'll be tapping my drum mag as well!

 

Loving the supressor!!!!

Link to comment
Share on other sites

On 05/03/2021 at 12:53, Skara said:

Magwells seem to be an issue for people running HPA taps or drum mags, most people just don't use them.

 

If it's a small amount of material that needs to be removed, I'd say go ahead and dremel the crap out of it (magwell, wouldn't touch the adapter).

 

Thank you @Skara for the words of encouragement. Seems an amount of dremeling resulted in me achieving my goal.

RvqMO_4246lKV9-i1HPe6NeWQhdrhlzEb8Fnye0j4M2sn4w1-8NJONRe6BbLoJKuV2klDvFwjAOsua7qpUGJGKS0Fzg_Iap5yufPMyZakNQfH54lQiGAAHUp_k7ik5Dt6itdxljHKVlb6Q85xe32Xeavcvy4EPxYhEADJ_Ld1uE_1Iwn_ZWYmD3YlpRJKBwbTHH5MPhzPE_5rEmGCGckdFHFxNWNUJyg-JgBOYETzGvBOUMUJeO36i0lXtFHqlO81gQxbZohgg5NRmb-2vLQ9Emq1km6UBhpLhqn7MBu_WqhRxhQetZHo-H2nOHVpm9OU8ZurChWOm6w1DpWYf404KhJtxW8ILrt_kp28qWlS14nWMzrOXBw6rtz5SHcoo5BZMjlQVRe8VvfcFnielAW610CrEt1xcCekMmcuHHiWYjrdjpDwy0qEXucC3wdWLx0070fMOjG_ahkraITHoS122zfyZUeZ6FtTsPHR1dn4YtPwb8ZqXU0FMjfSG57WhzRpaOXOpjOSkHAzzvk90zo1u8MOmyNacGHyb2X0svQ00iN13KqnU3Jc5cetfiNoUfsmbAY6ifMKGc0lWU1xtJZzlfwmkLLN9St-aebqfMGIEaLp5RXJOD6W-8mGSFwNymHtdHECYgcfIFBCNQt9dVKrQcvR0QE4mg6dufKYcvTrjC23hq7RkxuP_9KtnX81Q=w1356-h1015-no?authuser=0

 

mVxkeidXs6t8ckHLeF5WS2n8qW5l3EO6Ig3RVg_dhkenm5yZLE9-4G-CijI0r1gT3WTlnJiA17vKzV1lLFGH8lREfXzODY3sEmWCx0L_bgThuwujv5O3CYKt8eWgesu41KepJovEfcb_FF3xXQEPggItXippzEwoqwdZyI0cDfn0f8Szr_zsPXDTQ8MvwZcfOO92v5TU0VbVDEaFI7qWn6TSh4u7Y0_z4IHXROgA6cp6PmZbjabcza97m1iIVliGwoQw6XyK5pI15sMRP4_QW0UG9AVvxiuE53NZ-R2-q_UinmFIc3X1opbKVu4qo7EawKyDUUISG8pheq6mS9n1keP2IvPWPCAYp4pTPb0IoK9mgmREunr2hyjsmveeW-SMDwQF7BDqD9BLvAeRMzSed5FnSr5DtPnhkfmqLqtqBq4pTsSRKSFgyldH___ly5XkJasLQgkblFR8kQm3deIRXmrjY2cpxO-9NGfKjvhQ0hkyslRQrrfOK_zlQUvusoh7fCfF1tuBAOX5sRtUUmWCwlnQMWafYwdt3FENjFqUobuvlrD2zn5OMRDu8wv0v77wl6jRkemW2dpJPczPF4KBX-99J6qfI9ebHQmA0dBHwOKOzrllhWmo5A9Im6Lnu-Q0MD-dKDJUfklWTXvuiwSprEXNhUH6C_f3O-n117SyPRvhaKSxoVrcQKGBWDHxag=w1356-h1015-no?authuser=0

 

YbyjmOmwqoTHMJ_Ow09sBxUQ8_287vYZ2fpek2wwn5UY7hmu5_N6D_s5sa3jwiO5zT15YyPV5Ie-tJSEdMseyl5WYnwTlkJS2PFXTIciqc2aFididVX42qJEly4F1bNcTPpDgyoTOQV6OSNRvsmNwaoN6UNUlEHtUNbIvYkwmtwwIIGFB5LO0pAcd5Hga8d8YYtnbdCpJ7IpHmLPPJ0R-8vO_sMaPnnkz_bKgYt6aNY-F2WdtFT-3uikt1QJzgqkfoFrjabiAHCMVns3va-fFMCq6qnZ4vBJFm3RUesJ7qoLdToL1StR-UYOdeIg7pTcEKByEjyH4BLp_pUrugS4F2xODQanxIWZSTMRkgQ2RvIRXbACKMIQcUvclkoVJ8Cw6Y9HxjTabprT2TqDB2OTadVJYXhNJbThMrsGSEGzMwOCDe_KscvBqFYiJFoARvZ7H0NCTp7XSh2ak9drqy8EYMIUG-lc53Ex_cN-IV22pSCLnnHQzbJCZWNdHGxQkJfS2qaQiXmAoPFziNpUbCzXS0YGJ38NzqGRInElU8PRWoGG28HI2aQGcM1aDu3h4tE22EnU7tjKrmHfpTbFab4u2tCjOSWXnsF13mPfEa1WcuDw4TM1bQn2mL69Yethr_MW-Gqp8ANwM62-V5za3G10XYK4zaNtWbb6lzW1__i0HMXJmMKkMKmAf5D4TYfnRA=w759-h1014-no?authuser=0

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...