Jump to content

Kwc 1911 co2 - How to reduce fps?


Mad Rag
This thread is over three months old. Please be sure that your post is appropriate as it will revive this otherwise old (and possibly forgotten) topic.

Recommended Posts

Not long got this but it's a little hot for my CQB site , only 10fps over how can I bring this down a touch.

Link to comment
Share on other sites

What I would try is to file down the valve pin a bit.

Use a fine file and take your time so as not to damage the seating.

A dremel whould be good for this if done gently.

 

If it gets messed-up then you'll just have to replace the valve with a low pressure one.

Link to comment
Share on other sites

there is an npas for it but seems hard to get hold of. If you crop the floating valve spring in the nozzle you should be able to drop it by that much.

Link to comment
Share on other sites

thanks all for this. so i asked a few of the guys at the site and i was told you can drill holes in the barrel to fine tune it or put a restriction kit on it. im not very tech minded

53 minutes ago, EDcase said:

file down the valve pin a bit.

 where is the valve pin and how much would need to be taken off?

 

25 minutes ago, heroshark said:

crop the floating valve spring in the nozzle

again not sure on this where is this located. 

 

 

thanks again

Link to comment
Share on other sites

I wouldn't drill any holes in the barrel myself but it should reduce the power if that's the way you want to go. It may affect BB flight tho.

 

The pin is the the centre of the valve at the back of the magazine.  Its the bit you can push in when empty.

I'd guess to take off about half a mm but you'll need to chrono quite often to see how its affected.

 

As for the spring: you'll need to remove the valve with a valve key. (google search)

Link to comment
Share on other sites

1 hour ago, EDcase said:

Wouldn't you want a stronger spring to reduce output?

I'm thinking of the return spring...

weaker, closes sooner sending less out the barrel

 

Link to comment
Share on other sites

3 minutes ago, heroshark said:

weaker, closes sooner sending less out the barrel

 

I must be thinking of the wrong thing.  Doesn't the spring push the valve closed?

Link to comment
Share on other sites

1 hour ago, Mad Rag said:

 

again not sure on this where is this located. 

 

 

thanks again

 

It's in the nozzle in the blow back unit.

Link to comment
Share on other sites

32 minutes ago, EDcase said:

Ah, I was talking about the spring in the valve :D

I haven't tinkered with pistol internals yet.

 

Figured you were. That is another way to adjust it though. Having to do it on all mags and equally (unless you had a ready supply of springs you were fitting) would be hard and it would not make a big difference. Tbh cropping the floating valve spring is also minimal difference but dropping 10 fps you may just do it.

Link to comment
Share on other sites

Good point about having to modify all mags.

 

I'd still try modifying the valve itself for these two reasons: 

1. More gas efficient

2. Less stress on other parts to restrict gas flow.

 

Since it only needs reducing a small amount filing the valve pin would be my first try.

Link to comment
Share on other sites

1 minute ago, EDcase said:

Good point about having to modify all mags.

 

I'd still try modifying the valve itself for these two reasons: 

1. More gas efficient

2. Less stress on other parts to restrict gas flow.

What in?

 

Link to comment
Share on other sites

Sorry got befuddled thought you were referring to something you were working on. It's much easier modding something in the gun. For example if you wanted to lessen the actual gas out put filing the face of the valve knocker would be most effective.

Link to comment
Share on other sites

Yep, that's a good solution if the fps is consistently high with all mags.

 

Hard to get to tho?

Would need to do a complete tear-down to get to the hammer and then reassemble to test.

Link to comment
Share on other sites

  • 2 weeks later...

a wee update for you, used a different type of co2 bulb and the fps came down quite a bit.  

Link to comment
Share on other sites

Just now, EDcase said:

After  all that... 🤣

 i know i am just as shocked as you, went from 340 down to like 300-320

 

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

×
×
  • Create New...