Search results

I have an Article 1 and an MTW-9 but would like to swap the MTW-9 to M4 mags for cheap. Would any aeg lower fit the trigger components from an MTW?

11.1v is going to put more strain on the gun and potentially make it break faster. If you want the best trigger response: 11.1V If you want to try to prolong the life of your RIF: 7.4V You've put a fair amount of upgrades into it, and its your only RIF so I would say go for 7.4v. Or...

https://specnaarms.com/wp-content/uploads/2024/04/HAL1_manual_EN-PL.pdf HAL comes shipped in safe mode out of the box, connect the battery with the RIF in safe then wait for 3 seconds (for the beep) and hold the trigger for 5 seconds What did you do to the gearbox exactly? And which model RIF...

This is the "quality" content you'll be treated to: https://www.youtube.com/watch?v=7zT2ibYdz_Q

Nice I've always wondered about the GHM9-G . How heavy is the trigger on the GHM9-G vs GHM9-K variant? I had the GHM9-K and found the trigger to be a bit too heavy for longer shots

Once it was dispatched from toxicant it took only a couple of days, customs wasn't an issue. That said one of the guide rods isn't straight - so looks like I've got a lemon.

Pretty sure I am going to have to fill in an import form because I just had to fill in one for some blue training MWS pmags, and a hop up rubber. Not that bothered by it as long as they don't seize it! Thanks for the input guys.

Just ordered a Toxicant MCX direct from them and I am a bit confused as to whether it counts as a RIF when its missing an inner barrel? Maybe someone who's ordered one can tell me if customs got real upset about it (I've asked Toxicant to put my UKARA on it just in case).

@aidandeng Without looking at it and knowing exactly what part in the hammer assembly is worn, replacing the whole unit would probably be an easier solution: https://www.kyairsoft.com/accessories/components-parts/we-complete-hammer-assembly/we-f-series-complete-hammer-set-f226-f229.html Because...

Awesome, thanks for the initial review. What brand of mags were you using? 

Nowhere in the UK with the spring in stock but ✨SPAIN✨ https://www.replicantairsoft.com/webshop/en/inicios/2065-mp7a1-fire-selector-bar-spring-mgg1-81-tokyo-marui.html last one so grab it!

@Diablo675! Found a spring for you man: https://www.replicantairsoft.com/webshop/en/inicios/2065-mp7a1-fire-selector-bar-spring-mgg1-81-tokyo-marui.html In other news I ordered a Revanchist Gold Power Nozzle Valve for a VFC MP5 and because rumour has it they fit and could be interesting for...

A few lessons learnt from tinkering with my TM MP7: If you want to use propane and its shooting too hot, you can buy a pack of these as replacement rocket valve springs to cut them down to size to get the fps you are looking for: https://www.amazon.co.uk/dp/B076M27VH2 much cheaper and easier...

Just double checking before I buy a test batch, is ASG ultra air lower power than nuprol 2.0? I would have assumed so but patrol base have it listed as "more powerful than normal green gas".

Nothing you should need to lubricate before use, however if the nozzle is sticky you might want to lube that a tiny bit before you play so you don't get squishy trigger (like I did). So is the general consensus that ASG Ultra Air Power is less powerful than Nuprol 2.0? Even though some people...

Thanks for this, that makes me feel a lot better that it's not an anomaly.

https://gsp-airsoft-shop.de/detail/index/sArticle/1549 Here is the only place I could find that stocks alternate barrels. Would be nice if we can turn it into a PCC.

Is there any wearing on the outer-barrel? (can you see if the slide might be rubbing on the outer barrel)

Just got a new TM MP7A1 and on Green gas its shooting around 348fps on 0.2g at 11 degrees. I haven't seen any reviews where its been shooting this hot. I've since replaced the nozzle with an enhanced guarder one and started using white/blue gas, and cranked the hop a bit which gets me safely...