camden

My OEM upper is not working but my mate's is (on my lower receiver) so I know mine is gone. My question now is: do I buy a z-parts forged upper? Anyone got any experience with those? I would love an original TM but they are just not possible to get hold of.

My OEM upper is not working but my mate's is, so I know mine is gone. My question now is, do I buy a z-parts forged upper? anyone got any experience with those? Iwould love an original Tm but they are just not possible to get hold of.

Thanks for asking, Dave. Finally found the culprit and it was a 'duuh' moment: there wasn't an o-ring on the firing pin. All sorted now.

The MWS is currently not capable of emptying one mag. It usually manages at least 2 reloads on one gas refill. FPS is way down. have rebuilt bolt several times but no luck so far...

Thanks for your reply. Just received a replacement nozzle in the post and will try that today. i have alreadyt ried a complete Angry Gun nozzle setup but that had the same effect: no oomph.

My MWS is playing up and I think it is the BCG (as it works well with my mate's bolt). I tried gradually replacing everything and still no luck. I am looking for a recommendation of a GBB/MWS repair shop in the UK. Who would you go to? Anyone have a link to an original TM MWs nozzle? Thanks in advance, everyone!

My MWS is playing up and I think it is the BCG (as it works well with my mate's bolt). I tried gradually replacing everything and still no luck. I am looking for a recommendation of a GBB/MWS repair shop in the UK. Who would you go to? Thanks in advance, everyone! Anyone have a link to an original TM MWs nozzle?

BOLT ISSUES: Now this is really foxing me: I am using the original bolt (reinforced spring inside as the old one broke). With a fresh mag, it fires well for the first few shots and then performance drops hugely and it can't empty the mag. Using my mate's original bolt, (and using the same rifle and same magazine as before!!), it fires absolutely fine and empties the mag reliably. I have since changed to a light weight bolt (had one lying around so worth a try) and changed the pistol head/seal as well; with the same result. Anyone clever out there can point me in the right direction as I am really missing using my MWS? Thanks in advance!

Now this is really foxing me: I am using the original bolt (reinforced spring inside as the old one broke). With a fresh mag, it fires well for the first few shots and then performance drops hugely and it can't empty the mag. Using my mate's original bolt, (and using the same rifle and same magazine as before!!), it fires absolutely fine and empties the mag reliably. I have since changed to a light weight bolt (had one lying around so worth a try) and changed the pistol head/seal as well; with the same result. Anyone clever out there can point me in the right direction as I am really missing using my MWS? Thanks in advance!

Love your build, mate. Agree on many of your choices and am now looking out for a PTS ambi switch. where did you find yours, please? and CTR stocks just rock, whatever the weather

Just so that you can sleep better tonight: replacement screw is in the post from HAO 😂 There is an even cheaper version available on ebay I have just been made aware, just search for: Unity Style Fast Micro Aimpoint T1 / T2 High Rise Mount Only Black / FDE Airsoft

Hi Alphabear. I "misspoke" earlier: I own the PTS version/clone and am happy with it (so not the actual expensive RS Unity). ...and yes, there is a bolt missing in my HAO rail :(

I agree mostly on yout PTW Vs MWS comparison. I stopped using the MWS for woodland as not accurate enough over distance. However, I absolutely love the MWS for CQB.

I have gone back to original TM rubber after using the Tan Modify. Got chewed up after a few thousands rounds. so not a one-off the way this is looking. TM internals are generally very good. I stopped using my sexy Hao BCG for the same reason: just not good enough.

Could not agree with you more. I have an AG suppressor thast just about 'works' as in: it doesn't fall off.

There are a few versions of the HAO one. If you are a lightweight snowflake like myself, then go for the 'airsoft' version, which weighs about the same as the Angry G at 231grams but better made and closer to RS spec in terms of dimensions. However, if you are a true SAS warrior, then go for the 'hardcore' version (their words ) at 505 grams. The thing is: any real suppressor will make a rifle front-heavy and mess with its weight balance that far forward. https://www.haoptwart.com/product-page/hao-s-556rc-dummy-pre-order There is also a HAO 'trainer' that looks a bit rubbish (open at the front) weighing 'the same as a real one' (again, their words) https://www.haoptwart.com/product-page/hao-s-sf-suppressor-trainers By the way, I bought their MWS bolt carrier and it is pretty but no better than the original. Probably shoots less well but it is pretty (did I mention that already ?) and has a reinforced back end so less wear? The old adage of " internals: japan, externals: taiwan" still seems to hold true. Have ordered the PTS ambi selector and will report back once installed. Only works with the matching flash hider as mentioned by Captain Darling

It is the Angry gun suppressor, well spotted. I bought the matching flash hider with it and it fits very securely. Will post a picture asap. I would buy the HAO one these days if I hadn't already got the Angry G as the HAO one is RS sized (both flash hider and suppressor) whereas the Angry G is not.

Could not agree with you more. Had the Mk18 on my PTW for years and would just not go back. Now if somebody doesn't like the looks, that is fair enough but it works on the 'technical' side and handles a lot better. Both PTW and MWS now carry the rail, one has the short and one the long. HAO has worked wonders considering the price (not talking about their body kits here, which are ace but expensive. I will keep the original TM receiver on the MWS for a little while yet. The PTW has a HAO upper and lower now)

Thanks for that, will do asap!

I run a URGI myself

Thanks, Marine. I am surprised that the oem is the part to go for, though.

I need advice, please. i am aware that this question may be a repeat but the tech is changing constantly and I want the latest. My oem nozzle got mashed up and I need a stronger after market part. what si the latest product that anyone has had good results with, please? Thanks in advance!

I have had WE npas before and that is exactly what I did. In this case does not work as I can't 'grip' the npas unit.

Thanks, rocketdogbert for replying so quickly. I have the angled tool inserted at the end of the nozzle, but the whole npas unit is rotating when I turn the tool.