AirTech

Hi! After much deliberation I've decided to part with my Belarusian POSP scope. This is a real-steel scope manufactured by BelOMO in Belarus and is effectively a commercial version of the PSO-1. I bought this very shortly before Putin decided that Russia wasn't big enough, and it may be very difficult to get hold of these for a while due to the manufacturer having been put on a blacklist by the EU/UK/Canada/US etc. It has 4x magnification and a PSO-1 type reticle with the proper 1.8m calibrated range estimator. Optics are crystal clear and the reticle illuminates red (powered by 2 LR44 batteries). The illumination switch has 'on' and 'off' visible as opposed to the Cyrillic equivalents on the older/military versions. The scope will come with the SVD and AK mounting adapters as well as its carry case, instruction manual (Russian), adjustment tool, POSP branded lens cover (modified with a piece of clear perspex to protect the lens when flipped open) and a rubber eye piece which I've trimmed down very slightly at the back to get the eye relief correct. The scope itself has some marks and scuffs from skirmishing and the carry case has a small cut on one corner, presumably done by customs when it arrived in the UK. Sold as seen with no warranty either given or implied. Offers will be considered. Thank you for looking 😄

Cyma SVD scope mount with 20mm RIS rail. Very good condition having had light use. Attaches to the rail on the right side of the SVD receiver, confirmed to fit Cyma/S&T and King Arms SVD replicas. Very robust and over engineered mount! £30.00 posted, no warranty and no returns either given or implied Thanks 😄

Hi! Reluctantly up for sale is my Cyma SVD-S. It's served me very well since buying it new around 2 years ago and would be keeping it if I hadn't caught the Vietnam bug! Despite looking like a DMR it's been set up for use as a standard rifle and performs very well as such - semi auto only from the factory. Internally it's had the following mods: SHS high torque motor Gate PicoSSR3 mosfet, heavier gauge wiring and Deans connector SHS air-seal nozzle with o-ring Stainless steel inner barrel, 6.03mm - I believe this is Maple Leaf but can't remember exactly. It has an R-hop patch fitted so lifts heavier BBs well. General set-up - shimming/air seal etc. The replica will come with a Cyma SVD-specific RIS mount and 4 magazines in total (1 hicap, 3 midcap) as well as a surplus Soviet rifle sling. Original box, manual and cleaning rod also included. FPS is around 350 on a 0.20g BB but it works best with 0.28 and 0.30g. Not a replica you see every day and the side-folding stock helps with packing away for transport to and from your local site. Overall condition is very good with some small marks/scuffs from skirmishing. Collection preferred but I can post via ParcelForce 48 at the buyers' expense and risk. No returns and no warranty either given or implied. Thanks very much for looking

Russian/Soviet KZS concealment suit in size 2. For reference it's a good, roomy fit on me at 6' and 44'' chest. The idea with this is that it's worn over your regular fatigues so the fit is intentionally loose. I was told this particular example dates to around the mid 80's but I'm unable to confirm as the labels are quite faded. Overall condition is very good, elasticated waistband and trouser hems are still stretchy and the hood drawstrings/sleeve tags are still present and correct. One very small hole at the front where the hood attaches. £40.00 posted. Sold as seen, thanks for looking!

High quality SureFire Warden replica with embossed trademarks. Listed as used but it's only ever been test fitted so condition is excellent. Dimensions are 144x34mm, threading is 14mm CCW. End caps are threaded and can be unscrewed for adding foam/cardboard discs etc. £25.00 posted. Thanks for looking!

Russian Made SSO Gorka 2 suit. A very versatile and comfortable suit with hem stirrups and elasticated sections at the knees, hems and sleeves. Getting harder to find now for obvious reasons. Size is marked as 170/46, for reference I am 6' with a 34'' waist and 44'' chest and it's a good fit with some space left over for underlayers. Overall condition is very good aside for some signs of wear to both knees. The left knee picked up a relatively small tear which was sewn up (I must have left my knee pads at home that day!). £45 posted, sold as seen. Thanks for looking 😄

Hi, One pair of Danish M84 trousers for sale. They're marked 1985, not size marked unfortunately but as far I can make out with a measuring tape they're about 31/32 waist and 28 inside leg. Sadly they no longer fit me otherwise I'd definitely be keeping them! Clear signs of use with a couple of subtle repairs here and there - most notably just above the left knee. One or two buttons have also been replaced as well. Hem drawstrings and waist adjusters present and functional. Also listed elsewhere. Sold as seen with no returns or warranty. £25 posted. Thanks!

Here's my AGM STEN MK2 which I've regrettably decided to sell due to lack of use and needing the space! It's in skirmished condition with some some marks and scuffs as to be expected from in-game use. For something as simple and basic as it is, it shoots very well indeed at around 310-315fps on a 0.20g BB (although it'll lift anything up to around a 0.32 without issue). By design this gun has no safety and only shoots in full auto, but the ROF is such that it's possible to get single shots off with relative ease. Internally it's had the following mods: SHS piston with steel teeth High torque motor - I believe this is an SHS but I can't remember exactly ASG Ultimate spring Maple Leaf Macaron hop bucking - 60 degree ASG Ultimate o-ring air nozzle SHS steel spring guide with ball bearings Stock plastic bushings replaced with steel ones + gears shimmed Stock wiring replaced with slightly heavier gauge + Deans connector It'll come with 5 magazines, of which 4 are plastic 110 rounders and one is the original steel cased 50rd low cap. The 4 110rd magazines have had the stock follower springs replaced with MLS heavy springs to ensure reliable feeding. The top of the steel cased magazine is slightly cracked but still loads and feeds just fine (pictured). When I got the gun the mock bolt was missing, so I made a replacement from steel and epoxied it in place inside the receiver - looks pretty convincing and doesn't rattle around like the original. Also included is a repro STEN sling as well as 2 alternative stocks, a different skeleton style stock and a pistol grip (I bought these from a friend of mine and have yet to get around to modifying them to work with the gun, they'll need work to sort out battery storage!). The two alternative stocks are quite crudely made from folded/welded steel so could do with some extra finishing on the edges and perhaps a fresh lick of black paint. I also have original thumb screw that retains the stock, I replaced this with a button-head allen screw due to personal preference but this could be swapped back if you'd prefer. Hop is adjusted with a 2mm allen key (not included). Collection preferred on this but I could package up and post it if necessary. Sold as seen with no returns and no warranty either given or implied. Feel free to contact me with any questions. Thank you for looking!

Hi everyone, Here for sale is my modified JG MC51/G3 shorty. It's in good condition with a few light marks here and there picked up during about 4 skirmishes. I've owned this from new, and it's had the following internal modifications: High torque motor - IIRC this is either Rocket or SHS (though they're meant to be the same thing) SHS 12:1 gearset ZCI piston with steel rack Piston head o-ring has been changed for a slightly larger one for improved air seal SHS aluminium nozzle Gate PicoSSR3 mosfet + heavier wiring + Deans connector G&G green hop bucking The gun performs great and shoots at around 350fps on 0.2g BBs, semi auto is very snappy and it'll achieve over 25rps on an 11.1v battery. It has a modified-to-fit G&P Surefire replica handguard with an LED torch which is operated by a pressure bad on the right hand side. This also works great and has decent brightness. Original handguard included should you wish to swap it back. Claw mounted RIS rail attached to the top of the receiver. Also included are 3x 500rd hicap magazines as well as the original box, manual, mag winding key and cleaning rod. £160 posted. Open to sensible offers and collection also possible. No returns and no warranty either given or implied. Thank you for looking!

Hi all, Here's my 4x ACOG replica which I've decided to shift due to it not really suiting any of my setups or loadouts. Comes with a killflash which is in good shape and has working fibre optic illumination for the reticle. Glass is super clear. Great all round condition with very few small marks - the most noticeable is to the edge of the elevation adjustment cap. Great for DMR use or even just for spotting. £65 posted. Sold as seen with no warranty either given or implied. Thank you for looking

Set of polymer flip-up iron sights, these are spring loaded and flip up by pressing the release catch. Rear sight adjustable for windage, front adjustable for elevation. Rear sight is missing its securing screw but I'll do my best to find one for it. £9 posted. No returns and no warranty either given or implied. Thank you for looking

Cantilever style scope mount. 20mm RIS with quick release attachment, also has 2 small RIS sections on the top of the clamps for mounting small red dot etc. 30mm rings but supplied with spacers to take it down to 25mm. As new condition, unsure of brand as it has no markings. £13 posted. No returns and no warranty either given or implied. Thank you for looking

Replica Aimpoint CompM4. Excellent working condition, almost completely unmarked with some pretty convincing trades on it as well. 9 brightness settings and a screw on killflash in perfect condition. Supplied boxed with allen key, height spacer/longer screws and cleaning cloth. £37 posted. No returns and no warranty either given or implied. Thank you for looking

This is my G&G GK5C which I've decided to part with due to lack of use - dare I say that I've found it too 'modern' for my taste? Alongside the long top rail this has an enormous amount of rail space when the rail covers are removed for all of your torch/laser/PEQ box requirements. A great, quirky alternative to a SCAR or the usual rail-clad AR replicas. It's in very good used condition with some marks from skirmishing and it shoots beautifully, best with 0.28 and 0.30g BBs Internally it's had some modifications as follows: Rocket high torque motor - I believe this is a bright green painted version of an SHS high torque Perun mini mosfet - I went with the most compact unit I could find to preserve the already scant battery space Stainless one piece cylinder and cylinder head assembly SHS piston Maple Leaf Macaron hop bucking - 60 degree ZCI Stainless 6.03 inner barrel Gears have also been shimmed properly and AOE adjusted Brand new SHS trigger mechanism It'll be supplied with 2 G&G AK5 style 'waffle' hicaps as well as 5 Ares AMAG stubby midcaps. Also included is a Magpul MOE style foregrip which is a great colour match for the dark green on the gun as well as a complete spare hop up unit to keep for spares (unlikely to need this but good to have!) as well as a pair of VP 11.1v tri-leg batteries if the gun is collected (these fit good and snug under the front handguard). Chrono readings are around 350fps on 0.20g so should be suitable for use at most UK sites. There's one physical imperfection with the gun, which is that one of the sight 'ears' on the short range rear sight has broken off which is pictured. Bolt catch still working perfectly. Swap considered for an M14 style replica. Feel free to ask any questions, I'm more than happy to provide additional pictures or video clips if required. Realistic offers will be considered. Collection preferred but postage can be arranged at the buyers' expense and risk. Sold as seen with no returns either given or implied. Thank you for looking!

Hi everyone, 3x short 45rd Ares Striker mags for sale, one used, 2 as new. I believe these fit all 3 variants. £30 posted. These are sold as seen with no warranty either given or implied. Thank you for looking

Hi everyone, here for sale is my Ares AS-01. I bought this a few months ago intending to get back into the sniper role but have found myself using my AEGs exclusively. It's a light, handy rifle and an excellent performer. Internal upgraded parts are listed below: Action Army Striker hop up unit Maple Leaf Autobot hop bucking (60 degree IIRC) Maple Leaf 300mm 6.02 Stainless steel inner barrel AirsoftPro Piston AirsoftPro Spring guide M140 spring Amoeba Steel 1-piece sear In addition to this, the rifles' outer barrel has been shortened in order to make it more compact (also fits better with the shorter inner barrel). The pointless and flimsy cocking indicator has been removed and replaced with a steel pin which is retained by a screw (good, robust solution and not prone to falling out and getting lost like the stock piece). Supplied with its original 55rd magazine. The rifle is shooting at almost exactly 2J on a 0.40g BB, so should be site legal in most places. Bolt pull is fairly stiff due to the M140 spring but is easily manageable if you brace the rifle in your shoulder whilst cocking. The 2 allen keys are still present within the stock compartment, the 2mm for adjusting the TDC hop screw and the 3mm for disassembly of the rifle. Collection preferred but I can organise postage by ParcelForce Express48 if required. This is sold as seen with no warranty either given or implied. I'm more than happy to answer any questions or supply additional pictures, ask away! Thank you for looking

Hi everyone, here for sale is my Ares AS-01. I bought this a few months ago intending to get back into the sniper role but have found myself using my AEGs exclusively. It's a light, handy rifle and an excellent performer. Internal upgraded parts are listed below: Action Army Striker hop up unit Maple Leaf Autobot hop bucking (60 degree IIRC) Maple Leaf 300mm 6.02 Stainless steel inner barrel AirsoftPro Piston AirsoftPro Spring guide M140 spring Amoeba Steel 1-piece sear In addition to this, the rifles' outer barrel has been shortened in order to make it more compact (also fits better with the shorter inner barrel). It also comes with 4x Ares Striker magazines, 1 long and 3 short (2 of the short mags are brand new), as well as a compact 2-8x scope with a mildot reticle. The rifle is currently fitted with a lovely alpenflage sling made by Grave Solution, which will be included if the asking price is met. The pointless and flimsy cocking indicator has been removed and replaced with a steel pin which is retained by a screw (good, robust solution and not prone to falling out and getting lost like the stock piece). The rifle is shooting at almost exactly 2J on a 0.40g BB, so should be site legal in most places. Bolt pull is fairly stiff due to the M140 spring but is easily manageable if you brace the rifle in your shoulder whilst cocking. The 2 allen keys are still present within the stock compartment, the 2mm for adjusting the TDC hop screw and the 3mm for disassembly of the rifle. Collection preferred but I can organise postage by ParcelForce Express48 if required. This is sold as seen with no warranty either given or implied. I'm more than happy to answer any questions or supply additional pictures, ask away! Thank you for looking