M_P

Gun picture thread

4471 posts in this topic

Hop doesn't kick in immediately with a titled gun (at least when I've experimented) and if you're using canted irons/an RDS you'll only be aiming with that backup because somebody's too close for your other optic.

 

There'll probably be a bit of 'dead ground' in between the maximum straight flight distance of your BBs with the gun canted and the minimum useful range of the primary optic, but that's not too big of an issue IMHO.

Ian_Gere likes this

Share this post


Link to post
Share on other sites

gun2_zps14579022.jpg

 

Rebuilt Classic Army M15A1.

 

Added Magpul front end and Stock, shortened Barrel.

 

Still have to change wiring to front end but I think a LiPo will fit in to the Stock Tube, there is even a little cover in the end of the stock that snaps on and off to allow access.

Monty and Airsoft_Mr B like this

Share this post


Link to post
Share on other sites

If you remove the cover on the end of the buffer tube you'd probably be able to fit a small Lipo or stick Nimh in it.

HSCtheta7 likes this

Share this post


Link to post
Share on other sites

It's already removed and I have measured it up for a LiPo already :)

 

I will have to perform surgery somewhere to get the wires through.

Share this post


Link to post
Share on other sites

I got them when Gun Ho closed down they sold me two of their rental guns for £25. Cosmetics were a bit worn but the Gearboxes were still solid. I re-bushed and shimmed them, re-lubed and replaced one piston that had worn teeth.

All good to go again.

I sohuld add in the cost of the Magpul parts though :)

Share this post


Link to post
Share on other sites

krinkov time again! quite happy with how it turned out.. havn't paid too much attention to the left side thou, and might add more "dirty" in the future. but for now!

 

Pistol:

7xw9.jpg

Carbine right side:
xud2.jpg

Carbine left side:
bstw.jpg

Share this post


Link to post
Share on other sites

^^Porn :):wub:

two_zero likes this

Share this post


Link to post
Share on other sites

1459699_10153503095805206_313107464_n.jp

 

Primary and Sidearm :)

TeddyBhoy and Monty like this

Share this post


Link to post
Share on other sites

Well heres my RIFs

 

went for artistic hope you like.

 

 

 

 

post-7432-0-87052300-1385235392_thumb.jpg

Share this post


Link to post
Share on other sites

Ahhh,the Maru *CRRRRRRRRRRRRRKK CRKKKKKKKKKK* G *CRRRRRRREEEEEEee*. Nice piece of *CREEEEEEEEAAAAAAAAAAAA*ame it's so *CRREEEAAAAAAAAAAAA* creaky and the charging handle isn't too strong so HK slaps ha *CRRRRRRRRRRRRRRRRRRRRREEEEEK* minimum.

 

Seriously though, some company should get up off their arse and make a G3, not utilizing 20 year old standards and pot metal.

 

And make it full steel. For maximum HK shlaps.

 

And make a GBB one too.

 

Or TM should make a recoil shock G3. I'd trust them to not make the cocking handle pot metal.

Share this post


Link to post
Share on other sites

As we're on subject now- I'm still looking to make an MP5/G3 hybrid. Anyone know which manufacturer the Cyma MP5 is cloned from? Thinking of replacing my current front set (outer barrel, gas tube, cocking handle, front sight, handguard etc) with that of a G3's- kinda like this :

vrwqpt.jpg

Share this post


Link to post
Share on other sites

Ahhh,the Maru *CRRRRRRRRRRRRRKK CRKKKKKKKKKK* G *CRRRRRRREEEEEEee*. Nice piece of *CREEEEEEEEAAAAAAAAAAAA*ame it's so *CRREEEAAAAAAAAAAAA* creaky and the charging handle isn't too strong so HK slaps ha *CRRRRRRRRRRRRRRRRRRRRREEEEEK* minimum.

 

Seriously though, some company should get up off their arse and make a G3, not utilizing 20 year old standards and pot metal.

 

And make it full steel. For maximum HK shlaps.

 

And make a GBB one too.

 

Or TM should make a recoil shock G3. I'd trust them to not make the cocking handle pot metal.

Don't CA do one? Or should that be 'did one' as they seem to have sodded off somewhere.

As we're on subject now- I'm still looking to make an MP5/G3 hybrid. Anyone know which manufacturer the Cyma MP5 is cloned from? Thinking of replacing my current front set (outer barrel, gas tube, cocking handle, front sight, handguard etc) with that of a G3's- kinda like this

The CYMA is most likely TM, even the ICS is a tm clone so it'd make sense.

Share this post


Link to post
Share on other sites

Yeah, I had some suspicions about it after I was outranging all the other MP5 users at my local site, knowing the magic of the TM hops- but yeah, now there's just the small matter of finding and buying a TM G3SG1 front end :/

 

I may be fishing here but... trinityadam, would you be able to sell your G3's front end?

 

I can't find the damn parts anywhere.

 

I understand if you don't want to, I wouldn't :P

Share this post


Link to post
Share on other sites

i couldnt sell the front end on, it i really really like the g3.

 

but always in the market for something else. :D

Share this post


Link to post
Share on other sites

As we're on subject now- I'm still looking to make an MP5/G3 hybrid. Anyone know which manufacturer the Cyma MP5 is cloned from? Thinking of replacing my current front set (outer barrel, gas tube, cocking handle, front sight, handguard etc) with that of a G3's- kinda like this :

vrwqpt.jpg

 

what the....

Share this post


Link to post
Share on other sites

i couldnt sell the front end on, it i really really like the g3.

 

but always in the market for something else. :D

 

Fair enough mate, I'll just have to improve my Google-fu and try to find the parts elsewhere :D

But yeah, I completely understand. I knew I wasn't going to get the first stage of my DMR project done like that :)

 

 

what the....

Epic, no? I'm going to be using my MP5 as a base for a DMR project I'm starting next year- I really like the MP5 design, and I need to make it a lot larger so people won't get arsey about an SMG size DMR. Plus that long MP5 I posted on here looks a lot more interesting than AR15 or SR25 based DMRs.

Share this post


Link to post
Share on other sites

Well,you can buy a used/broken TM G3 on yahoo auctions japan and get Juno@bidservice.jp to ship it for you,then chop it up and jam it on your MP5.

Something like this-Only 1000JPY

http://page7.auctions.yahoo.co.jp/jp/auction/g127665032#enlargeimg

 

or this,the front end of a G3 without the foregrip

http://page13.auctions.yahoo.co.jp/jp/auction/r107764990

 

Or if you're a mad man,a PSG1 front end. Dunno if it will fit on an MP5.

http://page13.auctions.yahoo.co.jp/jp/auction/r108459797#enlargeimg

 

Another option is asking Pulse Japan to try find it for you.

 

You can also try find a used JG G3 and chop it up,but the plastic quality on those is sort of dreadful.

 

The most expensive option is probably buying a Classic Army G3 and chopping it up,but those are expensive and made of fragile monkey metal.

Share this post


Link to post
Share on other sites

That idea's probably gone down the drain now lol.

I could always just do this though:

Picture006.jpg

 

Just need to find myself a longer outer barrel and I'd be laughing.

 

edit: the outer barrel is off a G36K. Not sure how it'll work with my MP5 but I'm willing to give it a shot.

Share this post


Link to post
Share on other sites

I can sell you a G36K outer barrel, if you like. Not sure how much I'd want for it. I'll have a look around for comparisons if you're interested.

Share this post


Link to post
Share on other sites

You'd have to measure it up for me Ian- the measurements I need are in my MP5 thread.

Firesupport are asking for £31 for an Ares one- I can't find G36K OBs on other retailers I trust.

Share this post


Link to post
Share on other sites

You'd have to measure it up for me Ian- the measurements are in my MP5 thread.

Firesupport are asking for £31 for an Ares one- I can't find G36K OBs on other retailers I trust.

You could just buy barrel extensions if the G36 one doesn't fit, there are many others available.

Share this post


Link to post
Share on other sites

You could just buy barrel extensions if the G36 one doesn't fit, there are many others available.

Yeah, and use some kind of barrel accessory to cover the join - like a slim gas block, one of those bits with the tiny loop for an AK cleaning rod, a bayonet lug (maybe filed down), or just a barrel mount with a rail or loop.

M_P likes this

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now